C-IR-0203M is a module on the CIB bus with a total of 5 inputs / outputs in combination: 2 AI / DI inputs 2 relay outputs with changeover contact (each contact shown separately on the terminal board) 1 AO output with a range of 0 to 10V, or with a PWM output with adjustable amplitude and frequency. Use: Closed loop control with proportional control (PWM output) or two-point control (relay) Control of valves, motors, lighting switching, heating cartridges and other...

The C-IR-0303M is a module on the CIB bus that it contains - 3x AI / DI inputs - 3x relay outputs with switching contact (2 with common input and 1 separately connected to the terminal board). Use: - Valve control, addition of heating circuit control for common installations in the field of HVAC, - Switching of lighting, general loads and appliances - Measurement of up to three quantities by passive / resistance sensors

C-IB-1800M is a module on the CIB bus, which contains a total of 18 inputs 14 binary inputs - mainly for sensing potential-free contacts These inputs can be switched to the so-called balanced input mode used for security sensors. In this mode, the inputs can also detect sensor disconnection as tamper The module also has a power supply for security sensors requiring 12V DC 4 combined AI / DI inputs not only for binary and balanced inputs, but also for measuring passive...

C-IS-0504M is a module on the CIB bus with a total of 9 inputs / outputs in combination 3x combined AI / DI input for sensing contacts and measuring resistance thermometers, 2x analog input specialized for measuring AC resistances (excluding long-term electrolysis in a humid environment - icing, precipitation, level probes) 1x semiconductor output with pulse width modulation (PWM from 100 Hz to 2 kHz and load capacity max. 4W) 2x relay output 5 A, 1x relay output 16A,...

Module with a total of 8 relay outputs. It is connected to the basic module via a two-wire CIB Common installation BUS. Power supply either from the CIB bus (higher consumption limits the maximum number of modules on one CIB branch) or with amplification directly from a 24 V DC source. Each output has a make (16 A permanent) and break contact (10 A permanent). Each output has a separate LED indication on the front panel. The module can be switched to manual (service) mode...

C-OR-0011M-800; CIB, 11x RO, switching contact, 230V / 16A (inrush current 800A) Module on the CIB bus, which contains 11 relay outputs with a switching contact, each separately connected to the terminal board.

C-JC-0006M; CIB, 6x blind actuator, (6x2 RO - dependent switching, local function), 230VAC / 5A

C-RM-1109M; CIB, 3x AI, 8X DI, 1x AO, 8x RO, ext. power supply

C-HM-0308M; CIB, 3x AI/DI, 2x AO, 6x RO/5A

The C-HM-1113M modules are designed for connection to the CIB bus. The module contains - 8 binary inputs for contacts - 3 analog inputs with common terminal - 2 analog outputs with common terminal - 11 relay outputs grouped The outputs can be switched manually after switching to manual mode. The analog inputs are configurable according to the type of resistance sensor used, supplied from a common terminal. Analog outputs are with 8 bit resolution, voltage 0 ÷ 10V. The module is...

Module with a total of 32 inputs and outputs of digital, analog and relay in combination suitable to cover the needs of a typical hotel room or similar spaces.     It is connected to the basic module via the two-wire CIB Common installation BUS for communication.     The power supply is from the 230 V AC network to cover a higher consumption of a large number of inputs and especially relay outputs.     The module has 3 relays with a high permanent load capacity of 16A and resistance to...

The C-DM-0002L-10V module is designed for independent two-channel control of electronic LED ballasts or fluorescent lamps, controlled by 0-10 V DC or 1-10 V DC. To completely disconnect the ballasts from the main power supply, the module contains 2 relay outputs, one with an NC contact and the other with changeover contacts. Of course, analog inputs and relay outputs can also be used universally for other purposes. The module is designed for a DIN rail switchboard, but it can also be...

The C-DM-0006M-ULED module is a 6-channel dimming actuator 0-100% for LED strips in the supply voltage range of 12-48 V DC, with a load capacity of max. 4 A / channel. each channel can be controlled separately. It can also be used as a two-channel RGB actuator, or for two-channel control of the chromaticity of white lighting. The module is designed for a DIN rail switchboard and is connected to the basic module via a two-wire CIB Common Installation Bus®.

The C-DM-0006M-ILED module is a 6-channel controlled current source for direct control of the brightness of LED chips, ie continuous dimming 0-100% in adjustable ranges of 150 mA, 350 mA, 500 mA, 700 mA, which it generates from an external power supply 48 VDC / 5A. Each channel can be controlled separately. It can also be used as a two-channel RGB actuator, or for two-channel control of the chromaticity of white lighting, etc. The module is designed for a DIN rail switchboard and is...

The C-DM-0402M-RLC module is a 2-channel dimmer for phase control of the intensity of light sources with a resistive, inductive or capacitive character. It is possible to control a load of 2x 500 VA in a 230 V AC / 50 Hz network or a load of 2x 250 VA in a 115 V AC / 60 Hz network. The outputs can be interconnected and in a 230 V AC network the controlled load can be doubled to 1000 VA or even to 2000 VA by connecting all outputs on two modules and their coupled control via the CIB bus. In a...

The C-DL-0064M module is designed for address control of up to 64 ballasts connected to the DALI bus according to the specification: NEMA Standards Publication 243-2004 Digital Addressable Lighting Interface (DALI) Control Devices Protocol PART 2-2004. As of FW version v.1.5, the module can also be used as a CIB-DSI protocol converter. Signals from both CIB and DALI (DSI) buses are fed to the screw terminals. The power supply of the module is from an external 24 V DC source outside the...

The C-1W-4000M module is a 2-time low-speed 1Wire bus master designed by DALLAS. Each bus allows the connection of 20 sensors, ie a maximum of 40 sensors per module in total. The module is designed for a DIN rail switchboard. It is connected to the Foxtrot basic module via a two-wire CIB Common Installation Bus®.

Expansion module C-OS-0808M with 8 binary inputs at the level of 24 V DC and 2x4 fast transistor outputs usable for direct control of two unipolar or bipolar stepper motors. Inputs and outputs can also be used universally and can be set manually mode with the buttons on the front panel. The module is equipped with removable screw connectors. The module is designed for a DIN rail switchboard. It is connected to the Foxtrot basic module via a two-wire CIB Common Installation Bus®.

Modules C-FC-0024X is a composition of inputs and outputs designed to control the valves and fan of the FanCoil unit. If the composition of inputs and outputs is satisfactory, it can be used universally. The module contains 3 combined (analog / binary) inputs with a common terminal for connecting contacts or resistors. sensors, 1 analog / PWM output (8 bits, 0-10V) for continuous fan speed control and 2 relay outputs with a common terminal for controlling valves with heating and cooling...

The C-EV-0302M module is intended for controlling the charging of electric vehicles with alternating current according to ČSN EN 61851-1. For charging control and feedback, the module contains CP (Control Pilot) and PP (Proximity function) outputs connected to the charging connector (Type 1, Type 2). Furthermore, the module contains a relay output for controlling the contactor of the power supply to the electric vehicle and one semiconductor output for connection with an external charging...

The C-EV-0302M module is intended for controlling the charging of electric vehicles with alternating current according to ČSN EN 61851-1. For charging control and feedback, the module contains CP (Control Pilot) and PP (Proximity function) outputs connected to the charging connector (Type 1, Type 2). The module also contains relay outputs for controlling the power supply contactor for electric vehicles, one semiconductor output for controlling the charging connector lock, data output for...

Module of a 3-phase 4-quadrant fast electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms. The measurement is indirect, currents are sensed according to current transformers according to the required input range with a unified output of 333 mV. Data is transmitted via the two-wire CIB - Common Installation Bus®

The C-EM-0401M-P035 module is a fast 4-quadrant electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms for four phases. It can be used for one three-phase and one single-phase measurement at the same time as well as for four separate single-phase measurements. The measurement is indirect, the currents are sensed by bushing current transformers in the range up to 35 A, which are part of the delivery. The module has one relay output...

C-EM-0401M; CIB fast electricity meter / quality meter, power supply 230 V AC / DC, 4x U, 4x I - current transformer x: 100 mA, 1x RO The C-EM-0401M-P035 module is a fast 4-quadrant electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms for four phases. It can be used for one three-phase and one single-phase measurement at the same time as well as for four separate single-phase measurements. The measurement is indirect, currents are...