Навигация по разделу "Инструкции, софт и прошивки": Zipstore.ru > Инструкции, софт и прошивки > Меттлер Толедо > Протоколы для простых весов 

8213 Mettler

Host Communications

The 8217 scale acts as a peripheral device when connected to a host computer. When the host requests weight data by sending an uppercase W, the scale will respond with the weight data or a status byte if the scale is in motion or an invalid state. The host can also request a scale zero operation, in which case the scale will respond with the scale status, so the host can determine if the scale is in zeroing range and/or if the scale is at zero. A scale confidence test can also be initiated by the host to cause the scale to perform RAM, ROM, and NOVRAM tests and put the results in a status byte for later interrogation by the host.

Data is transmitted and received by the scale using an RS232 voltage level interface in the following ASCII format: 7 bit even parity and one stop bit. Data transmission rates are 1200, 2400, 9600, or 19200 baud asynchronous.  The host computer must send requests to the scale as specified single uppercase ASCII characters to have it perform various functions. The scale will send a response back to the host computer as a string of ASCII numeric digits or as an ASCII ? followed by a status byte. There must be at least a 200-ms delay between commands to allow for processing data response time at the scale. The following table shows the standard commands and responses between the scale and host.  If a confidence test results in an error, the scale will not respond to the W or Z commands until the error condition is corrected. An error will also cause the scale to halt any weighing operation until cleared.

Command Descriptions

ASCII Commands

(* MUST BE UPPERCASE CHARACTERS ONLY.)

*ASCII Command From Host	Scale Response	Description
W	STX 0WW.WW CR STX WW.WWW CR STX 0WW.WWN CR STX WW.WWWN CR STX?status byte CR	Instructs scale to send weight data. (W=Weight Digit 0-9). The scale will respond as follows according to setup and status:   Gross Weight Pounds. Gross Weight KG. Net Weight Pounds. ASCII N added after weight. Net Weight KG. ASCII N added after weight. Status byte is sent if scale is in motion, or is net/gross weight is negative or over capacity. Table “Scale Status Byte Bit Definitions” to determine status byte results.
Z	STX?status byte CR	Zero scale command. On the next A/D reading, zero will be captured if the weight is stable, within capture range, and no tare is taken (gross weight mode.)
TCR	STX?status byte CR	Tare item on platter command. The scale must be at gross zero before placing the item on the platter. Tare will be taken if weight is stable and non-zero. After 150 millisecond delay, the scale will respond with a status byte. (NOTE: Tare must be enabled in calibration mode or scale will not respond.).
TWWWWW CR	STX?status byte CR	Digital Tare Command. Known tare value can be sent to scale and must be transmitted as five digits. The scale assumes a decimal point of WWW.WW LB, or WW.WWW KG. (Note: Tare must be enabled in calibration mode or scale will not respond.)
C	STX?status byte CR	Clear Tare Command (ignored if weight is not stable.) Scale status byte is sent after 150 ms delay.
A	STX CR	Initiate Confidence Test Command. STXCR is sent indicating command was received.
B	STX?status byte CR	Send Confidence Test Results Command. A must be sent prior to the Send Result command B. Results of the test are contained in a status byte. Use Table “Scale Confidence Test Byte Bit Definitions” to determine test results. If all tests passed, the ASCII @ character will be returned. If a confidence test results in an error, the scale will not respond to the “W”, “H”, or “Z” command until the error condition is cleared.  A confidence test error will also cause the scale weighing operation to halt until the error condition is cleared.
E	STXECR	Start Echo Mode Serial Port Test Command. Scale will respond with an E indicating command received. Characters except F will be echoed back to the host.
F	STXF	End Echo Mode Command. The scale will respond with an ASCII F indicating the command was received.

 

Status Byte Format

When the scale responds with STX?status byte ^C_R , this indicates a status byte. The status byte contains scale status information, which can include net/gross mode, zero status, etc. The actual status byte sent will be an ASCII character which must be converted to binary to decode the bits. The scale status bit definitions are shown in the following table.

Scale Status Byte Bit Definitions

Confidence Test Status Byte Format

When the scale responds with STX? status byte ^C_R, after requesting a confidence test (B), a confidence test status byte will be sent. The status byte contains scale status information, which can include net/gross mode, zero status, etc. The actual status byte sent will be an ASCII character which must be converted to binary to decode the bits. The confidence test status bits are shown in the following table. Bit 6 is set to 1 after a confidence test is performed and reset to 0 after the host reads the confidence test status byte. The Confidence Test Byte bit definitions are shown below.

Note: The ASCII @ (decimal 64) indicates all tests were passed. Repeated reads of the confidence byte for all test passed without initiating a new confidence test will result in an ASCII NULL (hex 00).

Scale Confidence Test Byte Bit Definitions