Запасные части Pepperl+Fuchs

Сортировать по: Название Цена Блоки Таблица

Индуктивный датчик Inductive sensor NBN40-U1L-UU Pepperl+Fuchs

Каталожный номер: 246527

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.37
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Fe		1
Reduction factor r_Brass		0.4
Output type		2-wire
Nominal ratings
Switching frequency		0 ... 25 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V (typ. 2V) DC operation &le 8 V (typ. 2V) AC operation
Momentary current (20 ms, 0.1 Hz)		0 ... 3000 mA
Operating current		5 ... 500 mA
Off-state current		&le 1.5 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		flashes when overcurrent
Electrical specifications
Operating voltage		20 ... 300 V DC / 20 ... 253 V AC
Approvals and certificates
Protection class		II
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose "For use in NFPA 79 Applications only" For overcurrent protection, install a fuse with a rated current of max. 3 A and at least 300 V AC/DC
CCC approval		Ue 75VDC - 250VDC Ue 75VAC - 230VAC
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		terminal compartment
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA 6.6 / metal
Sensing face		PA 6.6
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-U1L-Z2 Pepperl+Fuchs

Каталожный номер: 233001

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.39
Reduction factor r_Cu		0.37
Reduction factor r₃₀₄		0.76
Nominal ratings
Operating voltage		5 ... 60 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Voltage drop at I_L
	Voltage drop I_L = 100mA, switching element on	... 5 V
Rated insulation voltage		60 V
Operating current		2 ... 200 mA
Off-state current		0 ... 1 mA typ. 0.7 mA
Switching state indicator		2 LED, yellow
Functional safety related parameters
MTTF_d		1170 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
Protection class		II
	Rated insulation voltage	60 V
	Rated impulse withstand voltage	800 V
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NCB40-FP-W-P1 Pepperl+Fuchs

Каталожный номер: 130542

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		flush
Output polarity		AC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.23
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 3 %
Short-circuit protection		no
Voltage drop		&le 5 V typ. 4V
Momentary current (20 ms, 0.1 Hz)		max. 4000 mA
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NBN40-U2L-UU Pepperl+Fuchs

Каталожный номер: 246528

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.37
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Fe		1
Reduction factor r_Brass		0.4
Output type		2-wire
Nominal ratings
Switching frequency		0 ... 25 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V (typ. 2V) DC operation &le 8 V (typ. 2V) AC operation
Momentary current (20 ms, 0.1 Hz)		0 ... 3000 mA
Operating current		5 ... 500 mA
Off-state current		&le 1.5 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		flashes when overcurrent
Electrical specifications
Operating voltage		20 ... 300 V DC / 20 ... 253 V AC
Approvals and certificates
Protection class		II
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose "For use in NFPA 79 Applications only" For overcurrent protection, install a fuse with a rated current of max. 3 A and at least 300 V AC/DC
CCC approval		Ue 75VDC - 250VDC Ue 75VAC - 230VAC
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		terminal compartment
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA 6.6 / metal
Sensing face		PA 6.6
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-U3-UU Pepperl+Fuchs

Каталожный номер: 248046

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.37
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Fe		1
Reduction factor r_Brass		0.4
Output type		2-wire
Nominal ratings
Switching frequency		AC, 0 ... 30 Hz DC, 0 ... 100 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V (typ. 2V) DC operation &le 8 V (typ. 2V) AC operation
Momentary current (20 ms, 0.1 Hz)		0 ... 3000 mA
Operating current		5 ... 500 mA
Off-state current		&le 1.5 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		flashes when overcurrent
Functional safety related parameters
MTTF_d		540 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		20 ... 300 V DC / 20 ... 253 V AC
Approvals and certificates
Protection class		I
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose
CCC approval		Ue 75VDC - 250VDC Ue 75VAC - 230VAC
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		terminal compartment
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA 6.6 / metal
Sensing face		PA 6.6
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-U4-UU Pepperl+Fuchs

Каталожный номер: 248047

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.37
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Fe		1
Reduction factor r_Brass		0.4
Output type		2-wire
Nominal ratings
Switching frequency		AC, 0 ... 30 Hz DC, 0 ... 100 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V (typ. 2V) DC operation &le 8 V (typ. 2V) AC operation
Momentary current (20 ms, 0.1 Hz)		0 ... 3000 mA
Operating current		5 ... 500 mA
Off-state current		&le 1.5 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		flashes when overcurrent
Functional safety related parameters
MTTF_d		540 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		20 ... 300 V DC / 20 ... 253 V AC
Approvals and certificates
Protection class		I
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose
CCC approval		Ue 75VDC - 250VDC Ue 75VAC - 230VAC
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		terminal compartment
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA 6.6 / metal
Sensing face		PA 6.6
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCB5-18GM40-N0-V1 Pepperl+Fuchs

Каталожный номер: 181107

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		5 mm
Installation		flush
Assured operating distance		0 ... 4.05 mm
Actual operating distance		4.5 ... 5.5 mm typ. 5 mm
Reduction factor r_Al		0.35
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Output type		2-wire
Nominal ratings
Nominal voltage		8.2 V (R_i approx. 1 k&Omega)
Switching frequency		0 ... 400 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		1880 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
FM approval
	Control drawing	116-0165
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 1D

Индуктивный датчик Inductive sensor NCB50-FP-A2-P1 Pepperl+Fuchs

Каталожный номер: 119181

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		50 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.38
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.83
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		670 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
Mass		445 g

Индуктивный датчик Inductive sensor NCB50-FP-A2-P1-V1 Pepperl+Fuchs

Каталожный номер: 187487

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		50 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.38
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.83
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		680 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68

Индуктивный датчик Inductive sensor NBN40-U4L-A2 Pepperl+Fuchs

Каталожный номер: 214024

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.39
Reduction factor r_Cu		0.37
Reduction factor r₃₀₄		0.75
Reduction factor r_Brass		0.45
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1310 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
Protection class		I
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U4L-UU Pepperl+Fuchs

Каталожный номер: 246529

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.37
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Fe		1
Reduction factor r_Brass		0.4
Output type		2-wire
Nominal ratings
Switching frequency		0 ... 25 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V (typ. 2V) DC operation &le 8 V (typ. 2V) AC operation
Momentary current (20 ms, 0.1 Hz)		0 ... 3000 mA
Operating current		5 ... 500 mA
Off-state current		&le 1.5 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		flashes when overcurrent
Electrical specifications
Operating voltage		20 ... 300 V DC / 20 ... 253 V AC
Approvals and certificates
Protection class		I
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose "For use in NFPA 79 Applications only" For overcurrent protection, install a fuse with a rated current of max. 3 A and at least 300 V AC/DC
CCC approval		Ue 75VDC - 250VDC Ue 75VAC - 230VAC
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		terminal compartment
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA 6.6 / metal
Sensing face		PA 6.6
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCB50-FP-E2-P1 Pepperl+Fuchs

Каталожный номер: 187388

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		50 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.38
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.83
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		940 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68

Индуктивный датчик Inductive sensor NCB50-FP-E2-P1-V1 Pepperl+Fuchs

Каталожный номер: 125750

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		50 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.38
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.83
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		940 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68

Индуктивный датчик Inductive sensor NBN40-U4L-Z2 Pepperl+Fuchs

Каталожный номер: 233002

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.39
Reduction factor r_Cu		0.37
Reduction factor r₃₀₄		0.76
Nominal ratings
Operating voltage		5 ... 60 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Voltage drop at I_L
	Voltage drop I_L = 100mA, switching element on	... 5 V
Rated insulation voltage		60 V
Operating current		2 ... 200 mA
Off-state current		0 ... 1 mA typ. 0.7 mA
Switching state indicator		2 LED, yellow
Functional safety related parameters
MTTF_d		1170 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
Protection class		II
	Rated insulation voltage	60 V
	Rated impulse withstand voltage	800 V
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN5-11K8-N-V8 Pepperl+Fuchs

Каталожный номер: 130051

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		5 mm
Installation		non-flush
Assured operating distance		0 ... 4.05 mm
Nominal ratings
Operating voltage		5 ... 15 V
Switching frequency		0 ... 2000 Hz
Hysteresis		0.05 ... 0.75
Current consumption
	Measuring plate not detected	min. 2.7 mA
	Measuring plate detected	&le 1.8 mA
Functional safety related parameters
MTTF_d		13570 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Solder connection
Housing material		PA
Housing diameter		10 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN5-F7-E2 Pepperl+Fuchs

Каталожный номер: 800731

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		5 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 500 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		< 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		3810 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.14 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN40+U1+N0 Pepperl+Fuchs

Каталожный номер: 106624

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		40 mm
Installation		non-flush
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.45
Reduction factor r₃₀₄		0.8
Nominal ratings
Installation conditions
	A	10 mm
Nominal voltage		8 V
Switching frequency		0 ... 100 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1860 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
FM approval
	Control drawing	116-0165
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 1D

Индуктивный датчик Inductive sensor NCN50-FP-W-P1 Pepperl+Fuchs

Каталожный номер: 130546

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		AC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 3 %
Short-circuit protection		no
Voltage drop		&le 5 V typ. 4V
Momentary current (20 ms, 0.1 Hz)		max. 4000 mA
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NBN8-12GM50-E0-M1 Pepperl+Fuchs

Каталожный номер: 293454-0038

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 24 mm x 24 mm x 1 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.45
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1200 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1484 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP68 / IP69K
Mass		70 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Индуктивный датчик Inductive sensor NBN8-18GK50-E2 Pepperl+Fuchs

Каталожный номер: 84463

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		3280 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP68 / IP69K
Note		use only delivered nuts

Индуктивный датчик Inductive sensor NBN8-18GM50-E0-V1 Pepperl+Fuchs

Каталожный номер: 84196

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 18 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		1920 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN8-18GM50-E2-V1 Pepperl+Fuchs

Каталожный номер: 84197

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm ( -25 ... 70 °C (-13 ... 158 °F) ) 0 ... 6.08 mm ( -40 ... -25 °C (-40 ... -13 °F) )
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 18 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		1190 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NEB22-30GM60-E2-V1 Pepperl+Fuchs

Каталожный номер: 23490

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		22 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 17.8 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.22
Reduction factor r₃₀₄		0.65
Nominal ratings
Installation conditions
	A	6 mm
	B	37 mm
	C	66 mm
	F	80 mm
Operating voltage		10 ... 30 V
Switching frequency		0 ... 150 Hz
Hysteresis		&le 10 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		0 ... 200 mA
Off-state current		&le 0.1 mA
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		213 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		chromium plated brass
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN8-18GM60-A2-V1 Pepperl+Fuchs

Каталожный номер: 84014

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 700 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1140 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NEB3-8GM45-E2-V1 Pepperl+Fuchs

Каталожный номер: 231694

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		3 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 2.4 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 9 mm x 9 mm x 1 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.8
Reduction factor r_Brass		0.5
Nominal ratings
Installation conditions
	A	in steel 1.0037 (St37): 1 mm
	B	6 mm
	C	9 mm
	F	16 mm
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 1500 Hz
Hysteresis		0.03 ... 0.3 mm
Reverse polarity protection		yes
Short-circuit protection		pulsing
Overload resistance		yes
Wire breakage protection		yes
Surge suppression		yes
Ripple		10 %
Voltage drop		&le 2 V
Repeat accuracy		0.15 mm
Operating current		0 ... 200 mA , above 50°C max. 150 mA
Off-state current		&le 10 µA
No-load supply current		&le 15 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1740 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		8 mm
Degree of protection		IP67
Mass		20 g

Индуктивный датчик Inductive sensor NEB3-8GM45-E2-V3 Pepperl+Fuchs

Каталожный номер: 231690

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		3 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 2.4 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 9 mm x 9 mm x 1 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.8
Reduction factor r_Brass		0.5
Nominal ratings
Installation conditions
	A	in steel 1.0037 (St37): 1 mm
	B	6 mm
	C	9 mm
	F	16 mm
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 1500 Hz
Hysteresis		0.03 ... 0.3 mm
Reverse polarity protection		yes
Short-circuit protection		pulsing
Overload resistance		yes
Wire breakage protection		yes
Surge suppression		yes
Ripple		10 %
Voltage drop		&le 2 V
Repeat accuracy		0.15 mm
Operating current		0 ... 200 mA , above 50°C max. 150 mA
Off-state current		&le 10 µA
No-load supply current		&le 15 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1740 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M8 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		8 mm
Degree of protection		IP67
Mass		20 g

Индуктивный датчик Inductive sensor NEB4-8GM45-E2 Pepperl+Fuchs

Каталожный номер: 123383

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		4 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 3.24 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.22
Reduction factor r₃₀₄		0.65
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.1 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		311 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.14 mm²
Housing material		chromium plated brass
Sensing face		PBT
Housing diameter		8 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCB1,5-18GM60-E2-D-V1 Pepperl+Fuchs

Каталожный номер: 134439

Описание оборудования
Inductive sensor

Индуктивный датчик Inductive sensor NCB1,5-8GM25-N0-V3-Y189382 Pepperl+Fuchs

Каталожный номер: 189382

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		1.5 mm
Installation		flush
Assured operating distance		0 ... 1.215 mm
Actual operating distance		1.35 ... 1.65 mm typ.
Reduction factor r_Al		0.22
Reduction factor r_Cu		0.19
Reduction factor r₃₀₄		0.65
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 2000 Hz
Hysteresis		1 ... 10 typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		Multihole-LED, yellow
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		Connector M8 x 1 , 3-pin
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		8 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NEB4-8GM50-E2-V3 Pepperl+Fuchs

Каталожный номер: 123384

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		4 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 3.24 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.22
Reduction factor r₃₀₄		0.65
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.1 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		311 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M8 x 1 , 3-pin
Housing material		chromium plated brass
Sensing face		PBT
Housing diameter		8 mm
Degree of protection		IP67

Pepperl+Fuchs — ориентир в промышленной автоматизации и взрывозащите

Pepperl+Fuchs — немецкий бренд с более чем 75-летней историей инженерного превосходства. Основанная в 1945 году в Мангейме, компания стала пионером бесконтактных датчиков и одним из мировых лидеров в области intrinsically safe решений для опасных сред. Сегодня Pepperl+Fuchs объединяет два направления — Factory Automation и Process Automation — предлагая датчики, интерфейсную электронику, системы взрывозащиты и HMI, которые повышают надежность, безопасность и эффективность производственных процессов.

Ключевые преимущества Pepperl+Fuchs

Инженерное качество: стабильные измерения, высокая повторяемость и минимальные ошибки в жестких условиях эксплуатации.
Безопасность и соответствие: решения с сертификатами ATEX, IECEx, UL и соответствием SIL/PL для критически важных применений.
Готовность к IIoT: поддержка IO-Link, AS-Interface, промышленного Ethernet и современных протоколов для прозрачности данных и предиктивного обслуживания.
Устойчивость к среде: широкий температурный диапазон, стойкость к вибрациям, влаге, пыли и химическим воздействиям (включая IP-защиту).
Совместимость и интеграция: бесшовная работа с ведущими ПЛК и системами управления, унифицированные интерфейсы и аксессуары.
Глобальная поддержка: доступность документации, сервисной сети и запасных частей для надежной долгосрочной эксплуатации.

Продуктовые направления

Датчики и системы распознавания: индуктивные, емкостные, магнитные, ультразвуковые и фотоэлектрические датчики; датчики расстояния, уплотнения контуров и позиционирования; энкодеры, 2D-ридеры и сканеры кода, RFID (HF/UHF), а также интеллектуальные решения с IO-Link. Для задач объемного контроля — лидарные сенсоры и визион-системы.
Интерфейсная техника и искробезопасность: гальванические изоляторы и барьеры (K-System, H-System, Zener), модули ввода/вывода, защита от перенапряжений, источники питания и диагностика шины FieldConnex для Foundation Fieldbus и PROFIBUS PA.
Оборудование для взрывоопасных зон: корпуса и клеммные коробки Ex e/Ex d из нержавеющей стали, алюминия и GRP; станции управления; системы продувки и наддува Bebco EPS; HMI и операторские панели для зон 1/21 и 2/22; мобильные устройства ecom для безопасной работы на площадках.
Связь и подключение: мастера и хабы IO-Link, компоненты AS-Interface, распределительные блоки, коннекторы и кабельная арматура для быстрого и чистого монтажа.
Функциональная безопасность: датчики и модули с подтвержденными уровнями SIL/PL, включая решения AS-i Safety at Work для защиты персонала и оборудования.

Области применения

Решения Pepperl+Fuchs используются в автомобильной промышленности, машиностроении, пищевой и фармацевтической отраслях, логистике и складской автоматизации, а также в нефтегазовом, химическом и горнодобывающем секторах, на объектах энергетики, водоснабжения и очистки стоков. Бренд одинаково эффективен для модернизации отдельных участков и для комплексной автоматизации линий и установок.

Почему это выгодно

Минимум простоев: надежная диагностика и предсказуемое обслуживание снижают незапланированные остановки.
Точность и качество: стабильные показания повышают выпуск и уменьшают брак.
Масштабируемость: широкий ассортимент позволяет развивать систему без смены платформы.
Долгий жизненный цикл: продуманная номенклатура и преемственность серий упрощают поставки и ремонт.
Полный комплект: от датчика и интерфейсных модулей до взрывозащищенных корпусов и операторских панелей.

Как выбрать решение Pepperl+Fuchs

Определите среду (включая наличие взрывоопасных зон), необходимые интерфейсы и уровень безопасности, диапазон измерений и точность, а также условия монтажа. Сверьте каталожные номера с требуемыми сертификатами и аксессуарами. При сложных задачах стоит привлечь инженера для подбора комплекта устройств с учетом специфики технологического процесса.

Pepperl+Fuchs — это инвестиция в надежность, безопасность и предсказуемые результаты. Выбирайте оригинальные решения бренда для уверенной работы оборудования сегодня и готовности к задачам завтрашнего дня.