Запасные части Pepperl+Fuchs

Сортировать по: Название Цена Блоки Таблица

Индуктивный датчик Inductive sensor NBB15-30GM50-A0-M1 Pepperl+Fuchs

Каталожный номер: 293454-0018

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		4-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		135 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA36HD-S***-CANopen Pepperl+Fuchs

Каталожный номер: T182422

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		10 E+8 revolutions
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		CANopen
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		DSP 406
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529 , IP68 / IP69K
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 300 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 30 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	powder coated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 6000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	180 N
	Radial	180 N

Индуктивный датчик Inductive sensor NBB15-30GM50-A0-V1-M1 Pepperl+Fuchs

Каталожный номер: 293454-0036

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		4-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		115 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA36HD-S***-J1939 Pepperl+Fuchs

Каталожный номер: T185454

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		10 E+8 revolutions
Diagnostic Coverage (DC)		0 %
Indicators/operating means
LED green		Operating mode
LED red		wrong baud rate
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		J1939
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		ISO 11898
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529 , IP68 / IP69K
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 300 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 30 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	powder coated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 6000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	180 N
	Radial	180 N

Индуктивный датчик Inductive sensor NBB15-30GM50-A2-M1 Pepperl+Fuchs

Каталожный номер: 293454-0019

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		4-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		135 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA36HD-S***-SSI Pepperl+Fuchs

Каталожный номер: T182024

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		700 a at 40 °C
Mission Time (T_M)		12 a
L₁₀		10 E+8 revolutions
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		4.75 ... 30 V DC
Power consumption		&le 1 W
Time delay before availability		< 450 ms
Output code		Gray code, binary code
Code course (counting direction)		adjustable
Interface
Interface type		SSI
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 16 Bit
	Overall resolution	up to 32 Bit
Transfer rate		0.1 ... 2 MBit/s
Cycle time		< 100 µs
Standard conformity		RS 422
Input 1
Input type		Selection of counting direction (cw/ccw)
Signal voltage
	High	4.75 V ... U_B (cw descending)
	Low	0 ... 2 V or unconnected (cw ascending)
Input current		< 6 mA
Switch-on delay		< 250 ms
Input 2
Input type		zero-set (PRESET 1) with falling edge
Signal voltage
	High	4.75 V ... U_B
	Low	0 ... 2 V
Input current		< 6 mA
Connection
Connector		M12 connector, 8-pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529 , IP68 / IP69K
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 300 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 30 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	powder coated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 6000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	180 N
	Radial	180 N

Индуктивный датчик Inductive sensor NBB15-30GM50-A2-V1-M1 Pepperl+Fuchs

Каталожный номер: 293454-0037

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		4-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		115 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA36IL-R***-CANopen Pepperl+Fuchs

Каталожный номер: T182404

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		1035 E+8 revolutions at 19/44 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		CANopen
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		DSP 406
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP54
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 3 Ncm
Shaft load
	Axial	19 N
	Radial	44 N
	Axial offset	± 0.3 mm static
	Radial offset	± 0.5 mm static

Индуктивный датчик Inductive sensor NBB15-30GM50-E0 Pepperl+Fuchs

Каталожный номер: 85971

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 200 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		990 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Однооборотный абсолютный шифратор Absolute encoders ENA36IL-R***-J1939 Pepperl+Fuchs

Каталожный номер: T185498

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		1035 E+8 revolutions at 19/44 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Indicators/operating means
LED green		Operating mode
LED red		wrong baud rate
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		J1939
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		ISO 11898
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP54
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 3 Ncm
Shaft load
	Axial	19 N
	Radial	44 N
	Axial offset	± 0.3 mm static
	Radial offset	± 0.5 mm static

Однооборотный абсолютный шифратор Absolute encoders ENA36IL-R***-SSI Pepperl+Fuchs

Каталожный номер: T168924

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		700 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		1035 E+8 revolutions at 19/44 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		4.75 ... 30 V DC
Power consumption		&le 1 W
Time delay before availability		< 450 ms
Output code		Gray code, binary code
Code course (counting direction)		adjustable
Interface
Interface type		SSI
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 16 Bit
	Overall resolution	up to 32 Bit
Transfer rate		0.1 ... 2 MBit/s
Cycle time		< 100 µs
Standard conformity		RS 422
Input 1
Input type		Selection of counting direction (cw/ccw)
Signal voltage
	High	4.75 V ... U_B (cw descending)
	Low	0 ... 2 V or unconnected (cw ascending)
Input current		< 6 mA
Switch-on delay		< 250 ms
Input 2
Input type		zero-set (PRESET 1) with falling edge
Signal voltage
	High	4.75 V ... U_B
	Low	0 ... 2 V
Input current		< 6 mA
Connection
Connector		M12 connector, 8-pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP54
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 3 Ncm
Shaft load
	Axial	19 N
	Radial	44 N
	Axial offset	± 0.3 mm static
	Radial offset	± 0.5 mm static

Индуктивный датчик Inductive sensor NBB15-30GM50-E0-M Pepperl+Fuchs

Каталожный номер: 240180

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 600 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Inductive overvoltage protection		yes
Surge suppression		yes
Voltage drop		&le 2 V
Rated insulation voltage		60 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 6 µA at 25 °C
No-load supply current		&le 7 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		830.5 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CSA approval		cCSAus Listed, General Purpose, Class 2 Power Source
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		3 x 0.75 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Mass		190 g

Индуктивный датчик Inductive sensor NBB15-30GM50-E0-M-Y242746 Pepperl+Fuchs

Каталожный номер: 242746

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		5 ... 30 V
Switching frequency		0 ... 200 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2.5 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		1260 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.75 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K

Однооборотный абсолютный шифратор Absolute encoders ENA36IL-S***-CANopen Pepperl+Fuchs

Каталожный номер: T182403

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		40 E-8 revolutions at 20/40 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		CANopen
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		DSP 406
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP54
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 3 Ncm
Shaft load
	Axial	20 N
	Radial	40 N

Однооборотный абсолютный шифратор Absolute encoders ENA36IL-S***-J1939 Pepperl+Fuchs

Каталожный номер: T185505

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		40 E-8 revolutions at 20/40 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Indicators/operating means
LED green		Operating mode
LED red		wrong baud rate
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		J1939
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		ISO 11898
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP54
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 3 Ncm
Shaft load
	Axial	20 N
	Radial	40 N

Индуктивный датчик Inductive sensor NBB15-30GM50-E0-M1 Pepperl+Fuchs

Каталожный номер: 293454-0014

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		135 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA36IL-S***-SSI Pepperl+Fuchs

Каталожный номер: T168923

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		700 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		40 E-8 revolutions at 20/40 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		4.75 ... 30 V DC
Power consumption		&le 1 W
Time delay before availability		< 450 ms
Output code		Gray code, binary code
Code course (counting direction)		adjustable
Interface
Interface type		SSI
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 16 Bit
	Overall resolution	up to 32 Bit
Transfer rate		0.1 ... 2 MBit/s
Cycle time		< 100 µs
Standard conformity		RS 422
Input 1
Input type		Selection of counting direction (cw/ccw)
Signal voltage
	High	4.75 V ... U_B (cw descending)
	Low	0 ... 2 V or unconnected (cw ascending)
Input current		< 6 mA
Switch-on delay		< 250 ms
Input 2
Input type		zero-set (PRESET 1) with falling edge
Signal voltage
	High	4.75 V ... U_B
	Low	0 ... 2 V
Input current		< 6 mA
Connection
Connector		M12 connector, 8-pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP54
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 150 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 3 Ncm
Shaft load
	Axial	20 N
	Radial	40 N

Индуктивный датчик Inductive sensor NBB15-30GM50-E0-V1 Pepperl+Fuchs

Каталожный номер: 85972

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 200 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		990 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Однооборотный абсолютный шифратор Absolute encoders ENA42HD-S***-CANopen Pepperl+Fuchs

Каталожный номер: T182481

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		10 E+8 revolutions
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		CANopen
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		DSP 406
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529 , IP66 / IP68 / IP69K
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 300 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 30 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	stainless steel 1.4404 / AISI 316L
	Flange	stainless steel 1.4404 / AISI 316L
	Shaft	Stainless steel 1.4412 / AISI 440B
Mass		approx. 350 g
Rotational speed		max. 6000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	270 N
	Radial	270 N

Однооборотный абсолютный шифратор Absolute encoders ENA42HD-S***-J1939 Pepperl+Fuchs

Каталожный номер: T185533

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		10 E+8 revolutions
Diagnostic Coverage (DC)		0 %
Indicators/operating means
LED green		Operating mode
LED red		wrong baud rate
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		J1939
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		ISO 11898
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529 , IP66 / IP68 / IP69K
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 300 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 30 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	stainless steel 1.4404 / AISI 316L
	Flange	stainless steel 1.4404 / AISI 316L
	Shaft	Stainless steel 1.4412 / AISI 440B
Mass		approx. 350 g
Rotational speed		max. 6000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	270 N
	Radial	270 N

Индуктивный датчик Inductive sensor NBB15-30GM50-E0-V1-M Pepperl+Fuchs

Каталожный номер: 240184

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 600 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Inductive overvoltage protection		yes
Surge suppression		yes
Voltage drop		&le 2 V
Rated insulation voltage		60 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 6 µA at 25 °C
No-load supply current		&le 7 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		830.5 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CSA approval		cCSAus Listed, General Purpose, Class 2 Power Source
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Mass		94 g

Индуктивный датчик Inductive sensor NBB15-30GM50-E0-V1-M1 Pepperl+Fuchs

Каталожный номер: 293454-0032

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		115 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA42HD-S***-SSI Pepperl+Fuchs

Каталожный номер: T179880

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		700 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		10 E+8 revolutions
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		4.75 ... 30 V DC
Power consumption		&le 1 W
Time delay before availability		< 450 ms
Output code		Gray code, binary code
Code course (counting direction)		adjustable
Interface
Interface type		SSI
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 16 Bit
	Overall resolution	up to 32 Bit
Transfer rate		0.1 ... 2 MBit/s
Cycle time		< 100 µs
Standard conformity		RS 422
Input 1
Input type		Selection of counting direction (cw/ccw)
Signal voltage
	High	4.75 V ... U_B (cw descending)
	Low	0 ... 2 V or unconnected (cw ascending)
Input current		< 6 mA
Switch-on delay		< 250 ms
Input 2
Input type		zero-set (PRESET 1) with falling edge
Signal voltage
	High	4.75 V ... U_B
	Low	0 ... 2 V
Input current		< 6 mA
Connection
Connector		M12 connector, 8-pin
Cable		&empty7 mm, 6 x 2 x 0.14 mm², 1 m (cable length, see order code)
Standard conformity
Degree of protection		DIN EN 60529 , IP66 / IP68 / IP69K
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 300 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 30 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	stainless steel 1.4404 / AISI 316L
	Flange	stainless steel 1.4404 / AISI 316L
	Shaft	Stainless steel 1.4412 / AISI 440B
Mass		approx. 350 g
Rotational speed		max. 6000 min ^-1
Moment of inertia		30 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	270 N
	Radial	270 N

Индуктивный датчик Inductive sensor NBB15-30GM50-E1-M Pepperl+Fuchs

Каталожный номер: 240181

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 600 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Inductive overvoltage protection		yes
Surge suppression		yes
Voltage drop		&le 2 V
Rated insulation voltage		60 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 6 µA at 25 °C
No-load supply current		&le 7 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		830.5 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CSA approval		cCSAus Listed, General Purpose, Class 2 Power Source
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		3 x 0.75 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Mass		190 g

Индуктивный датчик Inductive sensor NBB15-30GM50-E1-M1 Pepperl+Fuchs

Каталожный номер: 293454-0015

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		135 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA58IL-R***-CANopen Pepperl+Fuchs

Каталожный номер: T183818

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		480 a at 40 °C
Mission Time (T_M)		20 a
L₁₀		5 E+8 revolutions at 24/198 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		9 ... 30 V DC (with galvanic isolation)
Power consumption		&le 1.2 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		CANopen
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 15 Bit
	Overall resolution	up to 31 Bit
Transfer rate		min. 20 kBit/s , max. 1 MBit/s
Cycle time		&ge 1 ms
Standard conformity		DSP 406
Connection
Connector		M12 connector, 5 pin
Cable		&empty6 mm, 4 x 2 x 0.14 mm²
Standard conformity
Degree of protection		DIN EN 60529, IP65 or IP67
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 200 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 20 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		cable, flexing: -5 ... 70 °C (-23 ... 158 °F), cable, fixed: -30 ... 70 °C (-22 ... 158 °F) connector models: -40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	nickel-plated steel , painted
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 300 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		50 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	24 N
	Radial	198 N
	Angle offset	± 0.9 °
	Axial offset	± 0.3 mm static
	Radial offset	± 0.5 mm static

Индуктивный датчик Inductive sensor NBB15-30GM50-E1-V1-M Pepperl+Fuchs

Каталожный номер: 240185

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 600 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Inductive overvoltage protection		yes
Surge suppression		yes
Voltage drop		&le 2 V
Rated insulation voltage		60 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 6 µA at 25 °C
No-load supply current		&le 7 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		830.5 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CSA approval		cCSAus Listed, General Purpose, Class 2 Power Source
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Mass		94 g

Индуктивный датчик Inductive sensor NBB15-30GM50-E1-V1-M1 Pepperl+Fuchs

Каталожный номер: 293454-0033

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		115 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Однооборотный абсолютный шифратор Absolute encoders ENA58IL-R***-EtherCAT Pepperl+Fuchs

Каталожный номер: T175231

General specifications
Detection type		magnetic sampling
Device type		Absolute encoders
Linearity error		&le ± 0.1 °
Functional safety related parameters
MTTF_d		256 a at 40 °C
Mission Time (T_M)		12 a
L₁₀		5 E+8 revolutions at 24/198 N axial/radial shaft load
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		10 ... 30 V DC
Power consumption		approx. 4 W
Time delay before availability		< 250 ms
Output code		binary code
Code course (counting direction)		adjustable
Interface
Interface type		EtherCAT CoE (CANopen over EtherCAT, according to CiA DS-301 and DS-406 device profile CiA)
Resolution
	Single turn	up to 16 Bit
	Multiturn	up to 14 Bit
	Overall resolution	up to 30 Bit
Transfer rate		10 MBit/s / 100 MBit/s
Connection
Connector		Ethernet: 2 sockets M12 x 1, 4-pin, D-coded Supply: 1 plug M12 x 1, 4-pin, A-coded
Standard conformity
Degree of protection		DIN EN 60529, IP65, IP66, IP67
Climatic testing		DIN EN 60068-2-3, no moisture condensation
Emitted interference		EN 61000-6-4:2007
Noise immunity		EN 61000-6-2:2005
Shock resistance		DIN EN 60068-2-27, 100 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 10 g, 10 ... 1000 Hz
Ambient conditions
Operating temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		98 % , no moisture condensation
Mechanical specifications
Material
	Housing	Zinc plated steel, painted
	Flange	Aluminum
	Shaft	Stainless steel
Mass		approx. 300 g
Rotational speed		max. 12000 min ^-1
Moment of inertia		50 gcm²
Starting torque		< 5 Ncm
Shaft load
	Axial	24 N
	Radial	198 N
	Angle offset	± 0.9 °
	Axial offset	± 0.3 mm static
	Radial offset	± 0.5 mm static

Индуктивный датчик Inductive sensor NBB15-30GM50-E2-M1 Pepperl+Fuchs

Каталожный номер: 293454-0016

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		3-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		135 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Pepperl+Fuchs — ориентир в промышленной автоматизации и взрывозащите

Pepperl+Fuchs — немецкий бренд с более чем 75-летней историей инженерного превосходства. Основанная в 1945 году в Мангейме, компания стала пионером бесконтактных датчиков и одним из мировых лидеров в области intrinsically safe решений для опасных сред. Сегодня Pepperl+Fuchs объединяет два направления — Factory Automation и Process Automation — предлагая датчики, интерфейсную электронику, системы взрывозащиты и HMI, которые повышают надежность, безопасность и эффективность производственных процессов.

Ключевые преимущества Pepperl+Fuchs

Инженерное качество: стабильные измерения, высокая повторяемость и минимальные ошибки в жестких условиях эксплуатации.
Безопасность и соответствие: решения с сертификатами ATEX, IECEx, UL и соответствием SIL/PL для критически важных применений.
Готовность к IIoT: поддержка IO-Link, AS-Interface, промышленного Ethernet и современных протоколов для прозрачности данных и предиктивного обслуживания.
Устойчивость к среде: широкий температурный диапазон, стойкость к вибрациям, влаге, пыли и химическим воздействиям (включая IP-защиту).
Совместимость и интеграция: бесшовная работа с ведущими ПЛК и системами управления, унифицированные интерфейсы и аксессуары.
Глобальная поддержка: доступность документации, сервисной сети и запасных частей для надежной долгосрочной эксплуатации.

Продуктовые направления

Датчики и системы распознавания: индуктивные, емкостные, магнитные, ультразвуковые и фотоэлектрические датчики; датчики расстояния, уплотнения контуров и позиционирования; энкодеры, 2D-ридеры и сканеры кода, RFID (HF/UHF), а также интеллектуальные решения с IO-Link. Для задач объемного контроля — лидарные сенсоры и визион-системы.
Интерфейсная техника и искробезопасность: гальванические изоляторы и барьеры (K-System, H-System, Zener), модули ввода/вывода, защита от перенапряжений, источники питания и диагностика шины FieldConnex для Foundation Fieldbus и PROFIBUS PA.
Оборудование для взрывоопасных зон: корпуса и клеммные коробки Ex e/Ex d из нержавеющей стали, алюминия и GRP; станции управления; системы продувки и наддува Bebco EPS; HMI и операторские панели для зон 1/21 и 2/22; мобильные устройства ecom для безопасной работы на площадках.
Связь и подключение: мастера и хабы IO-Link, компоненты AS-Interface, распределительные блоки, коннекторы и кабельная арматура для быстрого и чистого монтажа.
Функциональная безопасность: датчики и модули с подтвержденными уровнями SIL/PL, включая решения AS-i Safety at Work для защиты персонала и оборудования.

Области применения

Решения Pepperl+Fuchs используются в автомобильной промышленности, машиностроении, пищевой и фармацевтической отраслях, логистике и складской автоматизации, а также в нефтегазовом, химическом и горнодобывающем секторах, на объектах энергетики, водоснабжения и очистки стоков. Бренд одинаково эффективен для модернизации отдельных участков и для комплексной автоматизации линий и установок.

Почему это выгодно

Минимум простоев: надежная диагностика и предсказуемое обслуживание снижают незапланированные остановки.
Точность и качество: стабильные показания повышают выпуск и уменьшают брак.
Масштабируемость: широкий ассортимент позволяет развивать систему без смены платформы.
Долгий жизненный цикл: продуманная номенклатура и преемственность серий упрощают поставки и ремонт.
Полный комплект: от датчика и интерфейсных модулей до взрывозащищенных корпусов и операторских панелей.

Как выбрать решение Pepperl+Fuchs

Определите среду (включая наличие взрывоопасных зон), необходимые интерфейсы и уровень безопасности, диапазон измерений и точность, а также условия монтажа. Сверьте каталожные номера с требуемыми сертификатами и аксессуарами. При сложных задачах стоит привлечь инженера для подбора комплекта устройств с учетом специфики технологического процесса.

Pepperl+Fuchs — это инвестиция в надежность, безопасность и предсказуемые результаты. Выбирайте оригинальные решения бренда для уверенной работы оборудования сегодня и готовности к задачам завтрашнего дня.