Купить Pepperl+Fuchs в интернет-магазине Zipstore.ru

Источник питания Power supply FB9205C Pepperl+Fuchs

Каталожный номер: 205891

Supply
Connection		wired to Ex e terminals
Rated voltage		95 ... 230 V AC
Power consumption		max. 45 VA
Inrush current		3.4 A (10 ms)
Input
Input frequency		50 ... 60 Hz
Output
Current		1.2 A
Voltage		24 V DC +/- 3% (Connectors 5, 12) 23 V DC +/- 3% decoupled via diode (Connectors 5, 13)
Indicators/settings
LED indicator		LED green: supply
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Low voltage
	Directive 2006/95/EC	EN 61010-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Mass		approx. 890 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2 G Ex d IIC Gb
Galvanic isolation
	Output/power supply	EN 60950-1 (safety requirement < 60 V)
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Интерфейсный модуль EasyCom Com Unit for PROFIBUS DP/DP-V1 FB8206H0629 Pepperl+Fuchs

Каталожный номер: 284166

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2 W
Fieldbus interface
Fieldbus type		PROFIBUS DP/DP-V1
PROFIBUS DP
	Connection	wired to Ex e terminals via backplane
	Baud rate	up to 1.5 MBit/s
	Protocol	PROFIBUS DP/DP V1 read/write services
Number of stations per bus line		max. 125 (PROFIBUS), max. 119 (service bus)
Cyclic process data		240 bytes input and (simultaneously) 240 bytes output
Number of stations per bus segment		max. 31 (RS-485 standard)
Number of repeaters between Master and Slave		max. 3
Supported I/O modules		all FB remote I/O modules
Bus length		max. 1000 m (FOL, 1.5 MBaud), max. 1000 m (copper cable, 187.5 kBd), max. 200 m (copper cable, 1.5 MBd)
Addressing		via configuration software
PROFIBUS address		0 ... 126 (factory standard setting: 126)
GSE file		CGV61711.gsd/gse
HART communication		via PROFIBUS or service bus
Internal bus
Connection		backplane bus
Redundancy		via front connector
Indicators/settings
LED indicator		LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no PROFIBUS connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB5-18GM60-A0 Pepperl+Fuchs

Каталожный номер: 83765

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.15
Reduction factor r₃₀₄		0.66
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 800 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1050 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Интерфейсный модуль Com Unit for MODBUS RTU FB8207H0706 Pepperl+Fuchs

Каталожный номер: 287613

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2 W
Fieldbus interface
Fieldbus type		MODBUS RTU
MODBUS RTU
	Connection	wired to Ex e terminals via backplane
	Baud rate	max. 38.4 kBit/s
Number of stations per bus line		max. 245 (MODBUS), max. 119 (service bus)
Number of channels per station		max. 80 analog, max. 184 digital (standard configuration)
Number of stations per bus segment		max. 31 (RS-485 standard)
Number of repeaters between Master and Slave		max. 3
Supported I/O modules		all FB remote I/O modules
Bus length		max. 1200 m (FOL, 38.4 kBd), max. 1200 m (copper cable, 38.4 kBd)
FOL (fiber optic link)		additional hardware required
Addressing		via configuration software
MODBUS address		standard compliant (factory standard setting: 126)
Service bus address		max. 119 , redundancy address = base + 128 (automatic)
HART communication		via service bus
Internal bus
Connection		backplane bus
Redundancy		via front connector
Indicators/settings
LED indicator		LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no Modbus RTU connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Интерфейсный модуль Com Unit for MODBUS TCP FB8211B2-0756 Pepperl+Fuchs

Каталожный номер: 287568

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2.5 W
Fieldbus interface
Fieldbus type		MODBUS TCP
Ethernet Interface
Connection type		wired to Ex e terminals via backplane
Transfer rate		10 MBit/s
Station connection		directly to PCS or PLC or via hubs or switches
Bus length		max. 100 m (Ethernet standard)
Addressing		IP address assigned via Ethernet
Ethernet address		IP V4 address (factory standard setting: 0.0.0.0, auto IP, DHCP)
Number of channels per station		max. 80 analog, max. 184 digital
Supported I/O modules		all FB remote I/O modules
HART communication		via Ethernet
Internal bus
Connection		backplane bus
Redundancy		via left front connector
Service interface
Connection		via right front connector in connection with service adapter SERV8001
Indicators/settings
LED indicator		LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no Modbus TCP connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2 G Ex d [ib] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN

Индуктивный датчик Inductive sensor NBB5-18GM60-A0-5M Pepperl+Fuchs

Каталожный номер: 119765

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.15
Reduction factor r₃₀₄		0.66
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 800 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ.
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1050 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 5 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Интерфейсный модуль Unicom Com Unit for PROFIBUS DP/DP-V1 FB8209H0907 Pepperl+Fuchs

Каталожный номер: 284167

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2 W
Fieldbus interface
Fieldbus type		PROFIBUS DP/DP-V1
PROFIBUS DP
	Connection	wired to Ex e terminals via backplane
	Baud rate	up to 1.5 MBit/s
	Protocol	PROFIBUS DP/DP V1 read/write services
Number of stations per bus line		max. 125 (PROFIBUS), max. 119 (service bus)
Cyclic process data		240 bytes input and (simultaneously) 240 bytes output
Number of stations per bus segment		max. 31 (RS-485 standard)
Number of repeaters between Master and Slave		max. 3
Supported I/O modules		all FB remote I/O modules
Configuration (240 bytes I/O)		Standard: 80 analog, 184 digital Universal 2I2O: 48 analog, 184 digital Universal 4I4O: 60 analog, 120 digital
Bus length		max. 1000 m (FOL, 1.5 MBaud), max. 1000 m (copper cable, 187.5 kBd), max. 200 m (copper cable, 1.5 MBd)
Addressing		via configuration software
PROFIBUS address		0 ... 126 (factory standard setting: 126)
GSE file		CGV61710.gsd/gse
HART communication		via PROFIBUS or service bus
Internal bus
Connection		backplane bus
Redundancy		via front connector
Indicators/settings
LED indicator		LED green (power supply): On = operating, fast flash = cold start, slow flash = HCIR loading active LED red (collective alarm): On = internal fault, flashing = no PROFIBUS connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Интерфейсный модуль Com Unit for PROFIBUS DP/DP-V1 FB8205* Pepperl+Fuchs

Каталожный номер: T34943

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2 W
Fieldbus interface
Fieldbus type		PROFIBUS DP/DP-V1
PROFIBUS DP
	Connection	wired to Ex e terminals via backplane
	Baud rate	up to 1.5 MBit/s
	Protocol	PROFIBUS DP/DP V1 read/write services
Number of stations per bus line		max. 125 (PROFIBUS), max. 119 (service bus)
Cyclic process data		240 bytes in total, either input or output data
Number of stations per bus segment		max. 31 (RS-485 standard)
Number of repeaters between Master and Slave		max. 3
Supported I/O modules		all FB remote I/O modules
Bus length		max. 1000 m (FOL, 1.5 MBaud), max. 1000 m (copper cable, 187.5 kBd), max. 200 m (copper cable, 1.5 MBd)
Addressing		via configuration software
PROFIBUS address		0 ... 126 (factory standard setting: 126)
GSE file		CGV61710.gsd/gse
HART communication		via PROFIBUS or service bus
Internal bus
Connection		backplane bus
Redundancy		via front connector
Indicators/settings
LED indicator		LED green (power supply): On = operating, fast flash = cold start, slow flash = HCIR loading active LED red (collective alarm): On = internal fault, flashing = no PROFIBUS connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB5-18GM60-A0-V1 Pepperl+Fuchs

Каталожный номер: 84011

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.15
Reduction factor r₃₀₄		0.66
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 800 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ.
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1050 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Интерфейсный модуль Com Unit for FOUNDATION Fieldbus Modular I/O FB8210* Pepperl+Fuchs

Каталожный номер: T42294

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2 W
Auxiliary energy		24 V DC Trunk load 20 mA
Fieldbus interface
Fieldbus type		FOUNDATION Fieldbus H1
FOUNDATION Fieldbus
	Connection	wired to Ex e terminals via backplane
	Baud rate	31.25 kBit/s , MBP
	Protocol	H1 to IEC 1158-2
Station connection		directly at the trunk or via spur protector
Number of stations per bus line		1 or 2, depending on the required response times
Number of channels per station		max. 20 analog, max. 40 digital
Supported I/O modules		5 slots, to be filled with (combinations possible): 108 digital input, 8-channel, NAMUR 305 analog input, 4-channel, 20 mA (HART via service bus) 405 analog output, 4-channel, 20 mA (HART via service bus) 5204 Pt100 RTD input, 4-channel 5205 thermocouple input, 4-channel 6305 relay output, 4-channel, 230 V 6306 relay output, 8-channel, 24 V 608 digital output, 8-channel, Ex i 6210-6215 digital output, 4-channel, Ex i power * = variable (2=IS, 3=Ex e)
Bus length		max. 1900 m (must not be exceeded by the sum of all trunk and spur lines)
Spur length		max. 120 m (depending on the number of field devices. Modular I/O station = 1 field device)
Addressing		via PCS (software)
Internal bus
Connection		backplane bus
Indicators/settings
LED indicator		LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no fieldbus LED yellow (operating mode): Flashing = active
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2 G Ex d IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Универсальный ввод/вывод Universal Input/Output (HART) LB7004A Pepperl+Fuchs

Каталожный номер: 254846

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Универсальный ввод/вывод Universal Input/Output (HART) LB7104A Pepperl+Fuchs

Каталожный номер: 254847

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006 EN 50303:2000
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB5-18GM60-A2 Pepperl+Fuchs

Каталожный номер: 83766

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.15
Reduction factor r₃₀₄		0.66
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 800 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1140 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator LB3002A2 Pepperl+Fuchs

Каталожный номер: 254699

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 13 ATEX E 038 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 EN 60079-11:2012 EN 60079-15:2010
International approvals
ATEX approval		BVS 13 ATEX E 038X
IECEx approval		BVS 13.0043X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator LB3005A2 Pepperl+Fuchs

Каталожный номер: 254700

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART):Supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14-3-wire transmitter:Supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16-Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-4-wire transmitter (powered externally):Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 105 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2012 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 105 X
IECEx approval		BVS 12.0055X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB5-18GM60-A2-10M Pepperl+Fuchs

Каталожный номер: 89611

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.15
Reduction factor r₃₀₄		0.66
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 800 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1140 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 10 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Компонент аналогового входа HART Transmitter Power Supply LB3006A Pepperl+Fuchs

Каталожный номер: 254702

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: channel I 1+, 2-, channel II 3+, 4-, channel III 5+, 6-, channel IV 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа Transmitter Power Supply, Input Isolator LB3101A2 Pepperl+Fuchs

Каталожный номер: 254704

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter: supply circuit: 2/3+, 4/5- 3-wire transmitter: supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6)
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		no
HART secondary variable		no
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 100 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Supply
	Voltage	23.8 V
	Current	90 mA
	Power	533 mW (linear characteristic)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 EN 50303:2000
International approvals
ATEX approval		BVS 12 ATEX E 100X
UL approval		E106378
IECEx approval		BVS 13.0043X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB5-18GM60-A2-5M Pepperl+Fuchs

Каталожный номер: 112714

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Reduction factor r_Al		0.25
Reduction factor r_Cu		0.15
Reduction factor r₃₀₄		0.66
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 800 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1140 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 5 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Компонент аналогового входа HART Transmitter Power Supply LB3102A1 Pepperl+Fuchs

Каталожный номер: 254705

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator LB3102A2 Pepperl+Fuchs

Каталожный номер: 254707

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 100 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	92 mA
	Power	619 mW (linear characteristic)
Connection 1-6
	Voltage	8.9 V
	Current	4 mA
	Power	24 mW (trapezoid characteristic curve)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 EN 50303:2000
International approvals
ATEX approval		BVS 12 ATEX E 100X
UL approval		E106378
IECEx approval		BVS 13.0043X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive analog sensor NBB5-18GM60-I Pepperl+Fuchs

Каталожный номер: 219078

General specifications
Output type		Analog current output
Installation		flush
Output polarity		DC
Measurement range		1 ... 5 mm
Output type		3-wire
Nominal ratings
Operating voltage		10 ... 30 V
Repeat accuracy		0 ... 20 µm
No-load supply current		&le 12 mA
Functional safety related parameters
MTTF_d		718 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Analog output
Output type		4 ... 20 mA
Linearity error		&le ± 4 % of full-scale value
Load resistor		&le 1000 &Omega
Temperature drift		&le ± 0.1 %/K of the measured value
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.5 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator LB3103A2 Pepperl+Fuchs

Каталожный номер: 254708

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 100 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Supply
	Voltage	24.9 V
	Current	77 mA
	Power	478 mW (linear characteristic)
Connection 1-6
	Voltage	8.9 V
	Current	4 mA
	Power	24 mW (trapezoid characteristic curve)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 EN 50303:2000
International approvals
ATEX approval		BVS 12 ATEX E 100X
UL approval		E106378
IECEx approval		BVS 13.0043X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа Transmitter Power Supply, Input Isolator LB3104A2 Pepperl+Fuchs

Каталожный номер: 254709

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter: supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14- 3-wire transmitter: supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16- measuring circuit: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16- 4-wire transmitter (separately powered): measuring circuit: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		no
HART secondary variable		no
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 024 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	90 mA
	Power	588 mW (linear characteristic)
Input
	Voltage	0.7 V
	Current	2.78 mA
	Power	2 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 EN 50303:2000
International approvals
ATEX approval		BVS 12 ATEX E 024 X
UL approval		E106378
IECEx approval		BVS 12.0055X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator LB3105A2 Pepperl+Fuchs

Каталожный номер: 254710

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART):Supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14-3-wire transmitter:Supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16-Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-4-wire transmitter (powered externally):Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 024 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	90 mA
	Power	588 mW (linear characteristic)
Input
	Voltage	0.7 V
	Current	2.78 mA
	Power	2 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 EN 50303:2000
International approvals
ATEX approval		BVS 12 ATEX E 024 X
UL approval		E106378
IECEx approval		BVS 12.0055X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа Universal Input/Output (HART) LB7004A Pepperl+Fuchs

Каталожный номер: 254846

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive analog sensor NBB5-18GM60-I-V1 Pepperl+Fuchs

Каталожный номер: 219079

General specifications
Output type		Analog current output
Installation		flush
Output polarity		DC
Measurement range		1 ... 5 mm
Output type		3-wire
Nominal ratings
Operating voltage		10 ... 30 V
Repeat accuracy		0 ... 20 µm
No-load supply current		&le 12 mA
Functional safety related parameters
MTTF_d		718 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Analog output
Output type		4 ... 20 mA
Linearity error		&le ± 4 % of full-scale value
Load resistor		&le 1000 &Omega
Temperature drift		&le ± 0.1 %/K of the measured value
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Компонент аналогового входа Universal Input/Output (HART) LB7104A Pepperl+Fuchs

Каталожный номер: 254847

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006 EN 50303:2000
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input LB1109A Pepperl+Fuchs

Каталожный номер: 223078

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		1.2 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		8
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
Connection		Terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-, 9+, 10-, 11+, 12-, 13+,14-, 15+, 16-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		15 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-8) red: line fault (lead breakage or short circuit) , yellow: signal (per channel)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with spring terminal (0.14 ... 0.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 13 ATEX 0036X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	10 V
	Current	12 mA
	Power	30 mW (linear characteristic)
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2011 EN 60079-11:2011 EN 60079-15:2010
International approvals
ATEX approval		EXA 13 ATEX 0036X
UL approval		E106378
IECEx approval		EXA 13.0003X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input LB1001A Pepperl+Fuchs

Каталожный номер: 254606

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 2/3- channel II: 4+, 5/6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1, 3) red: line fault (per channel) Status LED (2, 4) yellow: signal (per channel)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Запасные части Pepperl+Fuchs

Каталог запчастей Pepperl+Fuchs

Купить запчасти для Pepperl+Fuchs оптом и в розницу

Техподдержка