Запасные части Pepperl+Fuchs

Сортировать по: Название Цена Блоки Таблица

Индуктивный датчик Inductive sensor NBN40-L2M-E2-V1 Pepperl+Fuchs

Каталожный номер: 132360

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.28
Reduction factor r₃₀₄		0.75
Reduction factor r_Brass		0.38
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
	Off-state current T_U =40 °C, switching element off	&le
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA-GF35 metal base Xylan coated metal mounting flange Xylan coated.
Sensing face		PA-GF35
Housing diameter
Degree of protection		IP69K

Индуктивный датчик Inductive sensor NBN40-L3M-A2-C3-V1 Pepperl+Fuchs

Каталожный номер: 183739

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.35
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Brass		0.43
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 5 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1190 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		GD-ZnAl4Cu1, Coated metal fixing flange, coated.
Sensing face		Duroplast
Housing diameter
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-L3M-US-C3-V12 Pepperl+Fuchs

Каталожный номер: 908756

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 12.96 mm
Reduction factor r_Al		0.30 - 0.40
Reduction factor r₃₀₄		0.60 - 0.80
Nominal ratings
Operating voltage		20 ... 250 V AC/DC
Switching frequency		2 Hz
Hysteresis		3 ... 15 typ. 10 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		< 5 V
Operating current		3 ... 300 mA
Off-state current		&le 1.7 mA
No-load supply current		&le 0.6 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, red
Indicators/operating means
LED red/green		Short circuit/overload indication (alternate flashing)
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector 1/2"-20 UN , 3-pin
Housing material		Zinc, PTFE coated
Sensing face		Thermoset Plastic
Housing diameter
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-L3M-US-C3-V93 Pepperl+Fuchs

Каталожный номер: 908754

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 12.96 mm
Reduction factor r_Al		0.30 - 0.40
Reduction factor r₃₀₄		0.60 - 0.80
Nominal ratings
Operating voltage		20 ... 250 V AC/DC
Switching frequency		2 Hz
Hysteresis		3 ... 15 typ. 10 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		< 5 V
Operating current		3 ... 300 mA
Off-state current		&le 1.7 mA
No-load supply current		&le 0.6 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, red
Indicators/operating means
LED red/green		Short circuit/overload indication (alternate flashing)
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector 7/8"-16 UN , 3-pin
Housing material		Zinc, PTFE coated
Sensing face		Thermoset Plastic
Housing diameter
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-L3M-US-V12 Pepperl+Fuchs

Каталожный номер: 909763

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 12.96 mm
Reduction factor r_Al		0.30 - 0.40
Reduction factor r₃₀₄		0.60 - 0.80
Nominal ratings
Operating voltage		20 ... 250 V AC/DC
Switching frequency		30 Hz
Hysteresis		3 ... 15 typ. 10 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 7 V
Operating current		3 ... 300 mA
Off-state current		&le 1.7 mA
No-load supply current		&le 0.6 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, red
Indicators/operating means
LED red/green		Short circuit/overload indication (alternate flashing)
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector 1/2"-20 UN , 3-pin
Housing material		metal - Zinc housing
Sensing face		Thermoset Plastic
Housing diameter
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-L3M-US-V93 Pepperl+Fuchs

Каталожный номер: 909762

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 12.96 mm
Reduction factor r_Al		0.30 - 0.40
Reduction factor r₃₀₄		0.60 - 0.80
Nominal ratings
Operating voltage		20 ... 250 V AC/DC
Switching frequency		30 Hz
Hysteresis		3 ... 15 typ. 10 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 7 V
Operating current		3 ... 300 mA
Off-state current		&le 1.7 mA
No-load supply current		&le 0.6 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, red
Indicators/operating means
LED red/green		Short circuit/overload indication (alternate flashing)
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector 7/8"-16 UN , 3-pin
Housing material		metal - Zinc housing
Sensing face		Thermoset Plastic
Housing diameter
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-U1-A0 Pepperl+Fuchs

Каталожный номер: 194787

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1-A2-T Pepperl+Fuchs

Каталожный номер: 296378

General specifications
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		max. 2.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing) Tightening torque: 1.0 Nm (Screw terminal)

Индуктивный датчик Inductive sensor NBN40-U1-A2-V1 Pepperl+Fuchs

Каталожный номер: 203092

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1-B3B Pepperl+Fuchs

Каталожный номер: 226316

General specifications
Switching function		Normally open/closed (NO/NC) programmable
Output type		AS-Interface
Rated operating distance		40 mm
Installation		non-flush
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.45
Reduction factor r₃₀₄		0.85
Slave type		A/B slave
AS-Interface specification		V3.0
Required master specification		&ge V2.1
Nominal ratings
Operating voltage		26.5 ... 31.9 V via AS-i bus system
Switching frequency		0 ... 150 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
No-load supply current		&le 25 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		LED, red
Functional safety related parameters
MTTF_d		1330 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PBT
Housing diameter
Degree of protection		IP68 / IP69K

Индуктивный датчик Inductive sensor NBN40-U1-E0 Pepperl+Fuchs

Каталожный номер: 194777

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1-E0-M Pepperl+Fuchs

Каталожный номер: 217919

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.34
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.81
Reduction factor r_St37		1
Reduction factor r_Brass		0.4
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		870 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA-GF35
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1-E1 Pepperl+Fuchs

Каталожный номер: 194778

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1460 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1-E1-V1 Pepperl+Fuchs

Каталожный номер: 207650

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1460 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1-E2-V1 Pepperl+Fuchs

Каталожный номер: 203095

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm

Индуктивный датчик Inductive sensor NBN40-U1-E3 Pepperl+Fuchs

Каталожный номер: 194780

General specifications
Switching function		Normally closed (NC)
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
	Off-state current T_U =40 °C, switching element off	&le 100 µA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1980 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U10-E2 Pepperl+Fuchs

Каталожный номер: 203089

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U10-E2-25M Pepperl+Fuchs

Каталожный номер: 240276

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2.5 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 25 m
Core cross-section		3 x 0.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing) Tightening torque: 1.0 Nm (Screw terminal)

Индуктивный датчик Inductive sensor NBN40-U1K-N0-V1 Pepperl+Fuchs

Каталожный номер: 213836

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		40 mm
Installation		non-flush
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Output type		2-wire
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		yes
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 2.2 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1415 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 3G

Индуктивный датчик Inductive sensor NBN40-U1L-A0-T Pepperl+Fuchs

Каталожный номер: 256191

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.39
Reduction factor r_Cu		0.37
Reduction factor r₃₀₄		0.75
Reduction factor r_Brass		0.45
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		830 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
Protection class		II
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1L-A2-T Pepperl+Fuchs

Каталожный номер: 214021

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.39
Reduction factor r_Cu		0.37
Reduction factor r₃₀₄		0.75
Reduction factor r_Brass		0.45
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 60 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		830 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
Protection class		II
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U1L-A2-V1 Pepperl+Fuchs

Каталожный номер: 214023

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.39
Reduction factor r_Cu		0.37
Reduction factor r₃₀₄		0.75
Reduction factor r_Brass		0.45
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 100 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1310 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
Protection class		II
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA/metal
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing) Tightening torque: 1.0 Nm (Screw terminal)

Индуктивный датчик Inductive sensor NBN40-U2-A2 Pepperl+Fuchs

Каталожный номер: 203097

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Housing diameter
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U2-A2-T Pepperl+Fuchs

Каталожный номер: 296380

General specifications
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		max. 2.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing) Tightening torque: 1.0 Nm (Screw terminal)

Индуктивный датчик Inductive sensor NBN40-U2-E2 Pepperl+Fuchs

Каталожный номер: 203100

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.01 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U2-UU Pepperl+Fuchs

Каталожный номер: 248045

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC/DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.37
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.73
Reduction factor r_Fe		1
Reduction factor r_Brass		0.4
Output type		2-wire
Nominal ratings
Switching frequency		AC, 0 ... 30 Hz DC, 0 ... 100 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V (typ. 2V) DC operation &le 8 V (typ. 3 V) AC operation
Momentary current (20 ms, 0.1 Hz)		0 ... 3000 mA
Operating current		5 ... 500 mA
Off-state current		&le 1.5 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Error indicator		flashes when overcurrent
Functional safety related parameters
MTTF_d		540 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Electrical specifications
Operating voltage		20 ... 300 V DC / 20 ... 253 V AC
Approvals and certificates
Protection class		II
	Rated insulation voltage	230 V
	Rated impulse withstand voltage	2.5 kV
UL approval		cULus Listed, General Purpose "For use in NFPA 79 Applications only" For overcurrent protection, install a fuse with a rated current of max. 3 A and at least 300 V AC/DC
CCC approval		Ue 75VDC - 250VDC Ue 75VAC - 230VAC
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		terminal compartment
Core cross-section		up to 2.5 mm²
Housing material		PA 6.6 / metal
Sensing face		PA 6.6
Degree of protection		IP67

Индуктивный датчик Inductive sensor NBN40-U2K-N0 Pepperl+Fuchs

Каталожный номер: 213837

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		40 mm
Installation		non-flush
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		yes
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 2.2 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1415 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		&le 2.5 mm²
Housing material		PA
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing) Tightening torque: 1.0 Nm (Screw terminal)
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 3G

Индуктивный датчик Inductive sensor NBN40-U4-A2 Pepperl+Fuchs

Каталожный номер: 203101

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Housing diameter
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U4-A2-V1 Pepperl+Fuchs

Каталожный номер: 203102

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Индуктивный датчик Inductive sensor NBN40-U4-E0 Pepperl+Fuchs

Каталожный номер: 203104

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		40 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 32.4 mm
Actual operating distance		36 ... 44 mm typ. 40 mm
Reduction factor r_Al		0.31
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.39
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 180 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1510 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PA/metal with epoxy powder coating
Sensing face		PA
Degree of protection		IP68 / IP69K
Mass		225 g
Note		Tightening torque: 1.8 Nm (housing)

Pepperl+Fuchs — ориентир в промышленной автоматизации и взрывозащите

Pepperl+Fuchs — немецкий бренд с более чем 75-летней историей инженерного превосходства. Основанная в 1945 году в Мангейме, компания стала пионером бесконтактных датчиков и одним из мировых лидеров в области intrinsically safe решений для опасных сред. Сегодня Pepperl+Fuchs объединяет два направления — Factory Automation и Process Automation — предлагая датчики, интерфейсную электронику, системы взрывозащиты и HMI, которые повышают надежность, безопасность и эффективность производственных процессов.

Ключевые преимущества Pepperl+Fuchs

Инженерное качество: стабильные измерения, высокая повторяемость и минимальные ошибки в жестких условиях эксплуатации.
Безопасность и соответствие: решения с сертификатами ATEX, IECEx, UL и соответствием SIL/PL для критически важных применений.
Готовность к IIoT: поддержка IO-Link, AS-Interface, промышленного Ethernet и современных протоколов для прозрачности данных и предиктивного обслуживания.
Устойчивость к среде: широкий температурный диапазон, стойкость к вибрациям, влаге, пыли и химическим воздействиям (включая IP-защиту).
Совместимость и интеграция: бесшовная работа с ведущими ПЛК и системами управления, унифицированные интерфейсы и аксессуары.
Глобальная поддержка: доступность документации, сервисной сети и запасных частей для надежной долгосрочной эксплуатации.

Продуктовые направления

Датчики и системы распознавания: индуктивные, емкостные, магнитные, ультразвуковые и фотоэлектрические датчики; датчики расстояния, уплотнения контуров и позиционирования; энкодеры, 2D-ридеры и сканеры кода, RFID (HF/UHF), а также интеллектуальные решения с IO-Link. Для задач объемного контроля — лидарные сенсоры и визион-системы.
Интерфейсная техника и искробезопасность: гальванические изоляторы и барьеры (K-System, H-System, Zener), модули ввода/вывода, защита от перенапряжений, источники питания и диагностика шины FieldConnex для Foundation Fieldbus и PROFIBUS PA.
Оборудование для взрывоопасных зон: корпуса и клеммные коробки Ex e/Ex d из нержавеющей стали, алюминия и GRP; станции управления; системы продувки и наддува Bebco EPS; HMI и операторские панели для зон 1/21 и 2/22; мобильные устройства ecom для безопасной работы на площадках.
Связь и подключение: мастера и хабы IO-Link, компоненты AS-Interface, распределительные блоки, коннекторы и кабельная арматура для быстрого и чистого монтажа.
Функциональная безопасность: датчики и модули с подтвержденными уровнями SIL/PL, включая решения AS-i Safety at Work для защиты персонала и оборудования.

Области применения

Решения Pepperl+Fuchs используются в автомобильной промышленности, машиностроении, пищевой и фармацевтической отраслях, логистике и складской автоматизации, а также в нефтегазовом, химическом и горнодобывающем секторах, на объектах энергетики, водоснабжения и очистки стоков. Бренд одинаково эффективен для модернизации отдельных участков и для комплексной автоматизации линий и установок.

Почему это выгодно

Минимум простоев: надежная диагностика и предсказуемое обслуживание снижают незапланированные остановки.
Точность и качество: стабильные показания повышают выпуск и уменьшают брак.
Масштабируемость: широкий ассортимент позволяет развивать систему без смены платформы.
Долгий жизненный цикл: продуманная номенклатура и преемственность серий упрощают поставки и ремонт.
Полный комплект: от датчика и интерфейсных модулей до взрывозащищенных корпусов и операторских панелей.

Как выбрать решение Pepperl+Fuchs

Определите среду (включая наличие взрывоопасных зон), необходимые интерфейсы и уровень безопасности, диапазон измерений и точность, а также условия монтажа. Сверьте каталожные номера с требуемыми сертификатами и аксессуарами. При сложных задачах стоит привлечь инженера для подбора комплекта устройств с учетом специфики технологического процесса.

Pepperl+Fuchs — это инвестиция в надежность, безопасность и предсказуемые результаты. Выбирайте оригинальные решения бренда для уверенной работы оборудования сегодня и готовности к задачам завтрашнего дня.