Тип запчасти - Кабель

Set: Supply module and strain relief housing 770-505Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any location of the flat cable – one rotation per pole is all that is required...

Set: Supply module and strain relief housing 770-505Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any location of the flat cable – one rotation per pole is all that is required...

Set: Supply module and strain relief housing 770-505Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any location of the flat cable – one rotation per pole is all that is required...

Set: Supply module and strain relief housing 770-505Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any location of the flat cable – one rotation per pole is all that is required...

Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any point along the flat cable – one rotation per pole is all that is required....

Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any point along the flat cable – one rotation per pole is all that is required....

Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any point along the flat cable – one rotation per pole is all that is required....

Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any point along the flat cable – one rotation per pole is all that is required....

Suitable for bus and power lines or for bus and power combined in one cableEasy installation without line interruption due to convenient insulation displacement technology (IDC)WINSTA® IDC Supply and Tap-Off Modules allow connection at any point along the flat cable – one rotation per pole is all that is required....

Примечание: чтобы гарантировать безопасное функционирование, необходимо учесть, что остаточные напряжения (образуются из-за емкости кабеля с длинными соединительными линиями или токов утечки полупроводниковых переключателей и их схем защиты) должны быть ниже, чем напряжение отпускания реле. Для реле с постоянным током, напряжение отпускания определено значением ?5% номинального напряжения; для реле с переменным током оно составляет 15% номинального напряжения (в соответствии с VDE 0435).Если высокое остаточное напряжение существует, возможно, что реле не сможет вернуться в исходное положение. В зависимости от причины образования остаточного напряжения устранить данную проблему может изменение схемы кабельной разводки или параллельное подключение элемента RC.Примечание:To guarantee safe operation, residual voltages (due to the cable capacitance of long connection lines or leakage currents of semi-conductor switches and their protective circuits) must be lower than the release voltage of the relays.For DC relays, the release voltage is specified with ? 5% of the nominal voltage; for AC relays, it is 15% of the nominal voltage (per VDE 0435).The relay may not reset if a high residual voltage exists. Depending on the reason for the residual voltage, changing the cable routing or a parallel connection of an RC element could remedy this situation....