Запасные части Pepperl+Fuchs

Сортировать по: Название Цена Блоки Таблица

Индуктивный датчик Inductive sensor NCN40+U4+N0 Pepperl+Fuchs

Каталожный номер: 85986

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		40 mm
Installation		non-flush
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.45
Reduction factor r₃₀₄		0.8
Output type		2-wire
Nominal ratings
Installation conditions
	A	10 mm
Nominal voltage		8 V
Switching frequency		0 ... 100 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		LED, yellow
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT-GF20, Crastin SK 643 FR
Sensing face		PBT-GF20, Crastin SK 643 FR
Degree of protection		IP68

Индуктивный датчик Inductive sensor NCN40-FP-W-T-P1 Pepperl+Fuchs

Каталожный номер: 130539

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 3 %
Short-circuit protection		no
Voltage drop		&le 5 V typ. 4V
Momentary current (20 ms, 0.1 Hz)		max. 3000 mA
Temperature drift		-10 ... 15 % at < -25 °C
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NCN40-FP-W-T-P4 Pepperl+Fuchs

Каталожный номер: 130540

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		40 mm
Installation		non-flush
Output polarity		AC
Assured operating distance		0 ... 32.4 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 3 %
Short-circuit protection		no
Voltage drop		&le 5 V typ. 4V
Momentary current (20 ms, 0.1 Hz)		max. 3000 mA
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT/base of metal
Sensing face		PBT
Degree of protection		IP68
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NCN50-FP-A2-P1 Pepperl+Fuchs

Каталожный номер: 187587

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		680 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
Mass		410 g

Индуктивный датчик Inductive sensor NCN50-FP-A2-P1-V1 Pepperl+Fuchs

Каталожный номер: 129433

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		680 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68

Индуктивный датчик Inductive sensor NCN50-FP-A2-P3 Pepperl+Fuchs

Каталожный номер: 129435

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		680 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT/base of metal
Sensing face		PBT
Degree of protection		IP68

Индуктивный датчик Inductive sensor NCN50-FP-A2-P4 Pepperl+Fuchs

Каталожный номер: 182956

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		680 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Information for connection		A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %
Core cross-section		up to 2.5 mm²
	Minimum core cross-section	without wire end ferrule 0.5 mm² , with connector sleeves 0.34 mm²
	Maximum core cross-section	without wire end ferrule 2.5 mm² , with connector sleeves 1.5 mm²
Housing material		PBT/base of metal
Sensing face		PBT
Degree of protection		IP68

Индуктивный датчик Inductive sensor NCN50-FP-N0-P4-V1 Pepperl+Fuchs

Каталожный номер: 184679

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		50 mm
Installation		non-flush
Assured operating distance		0 ... 40.5 mm
Actual operating distance		45 ... 55 mm typ.
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.8
Output type		2-wire
Nominal ratings
Installation conditions
	A	40 mm
	B	150 mm
	F	240 mm
Nominal voltage		8.2 V (R_i approx. 1 k&Omega)
Switching frequency		0 ... 80 Hz
Hysteresis		0 ... 5 typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	&ge 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		LED, yellow
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
FM approval
	Control drawing	116-0165
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PBT/metal
Sensing face		PBT
Degree of protection		IP67
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 1D

Индуктивный датчик Inductive sensor NCN50-FP-W-P2 Pepperl+Fuchs

Каталожный номер: 182959

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		AC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 3 %
Short-circuit protection		no
Voltage drop		&le 5 V typ. 4V
Momentary current (20 ms, 0.1 Hz)		max. 4000 mA
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP68
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NCN50-FP-W-P4 Pepperl+Fuchs

Каталожный номер: 182960

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		AC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Operating voltage AC		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 3 %
Voltage drop		&le 5 V typ. 4V
Momentary current (20 ms, 0.1 Hz)		max. 4000 mA
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		max. 2.5 mm²
Housing material		PBT/metal
Sensing face		PBT
Degree of protection		IP68
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NCN50-FP-W-P4-BHMS3-N.O. Pepperl+Fuchs

Каталожный номер: 908506

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		AC
Assured operating distance		0 ... 40.5 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Output type		2-wire
Nominal ratings
Operating voltage AC		20 ... 253 V
Switching frequency		0 ... 20 Hz
Hysteresis		3 ... 15 % 5 % typical
Voltage drop		&le 5 V
Momentary current (20 ms, 0.1 Hz)		max. 4000 mA
Operating current		5 ... 500 mA
Off-state current		0.3 ... 1 mA typ. 0.7 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		7/8 inch-16 UN , 3-pin
Housing material		PBT/base of metal
Sensing face		PBT
Degree of protection		IP67
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 2 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Индуктивный датчик Inductive sensor NCN50-FP-Z2-P1 Pepperl+Fuchs

Каталожный номер: 180626

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Actual operating distance		45 ... 55 mm typ.
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.8
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		0 ... 20 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 6 V
Operating current		2 ... 200 mA
Off-state current		0.4 ... 1 mA typ. 0.6 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN50-FP-Z2-P4 Pepperl+Fuchs

Каталожный номер: 906229

General specifications
Switching function		Normally open/closed (NO/NC)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Actual operating distance		45 ... 55 mm typ.
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.8
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		0 ... 20 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 6 V
Operating current		2 ... 200 mA
Off-state current		0.4 ... 1 mA typ. 0.6 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		screw terminals
Core cross-section		up to 2.5 mm²
Housing material		PBT/metal
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN50-FP-Z4-V1 Pepperl+Fuchs

Каталожный номер: 182918

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		50 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 40.5 mm
Actual operating distance		45 ... 55 mm typ.
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.8
Nominal ratings
Operating voltage		10 ... 60 V
Switching frequency		0 ... 80 Hz
Hysteresis		0 ... 20 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 4.3 V
Voltage drop at I_L
	Voltage drop I_L = 20mA, switching element on	2.7 ... 4.2 V
Operating current		2 ... 200 mA
Lowest operating current		2 mA
Off-state current		0.4 ... 1 mA typ. 0.6 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PBT
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-12GM35-Z4 Pepperl+Fuchs

Каталожный номер: 109739

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.49
Reduction factor r_Cu		0.49
Reduction factor r₃₀₄		0.74
Nominal ratings
Operating voltage		3.5 ... 30 V
Switching frequency		0 ... 750 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		conducting
Short-circuit protection		pulsing
Voltage drop		&le 3.5 V
Temperature drift		± 15%
Operating current		2 ... 100 mA
Off-state current		0.4 ... 0.6 mA typ. 0.5 mA
Switching state indicator		LED, yellow
Pre-fault indicator		LED, red
Stability control-switch point		0,8 s_r ... 0,9 s_r
Functional safety related parameters
MTTF_d		1010 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-12GM35-Z5 Pepperl+Fuchs

Каталожный номер: 121013

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.49
Reduction factor r_Cu		0.49
Reduction factor r₃₀₄		0.74
Nominal ratings
Operating voltage		3.5 ... 30 V
Switching frequency		0 ... 750 Hz
Reverse polarity protection		conducting
Short-circuit protection		pulsing
Voltage drop		&le 3.5 V
Temperature drift		± 15%
Operating current		2 ... 100 mA
Off-state current		0.4 ... 0.6 mA typ. 0.5 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-12GM40-Z4-V1 Pepperl+Fuchs

Каталожный номер: 121011

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.49
Reduction factor r_Cu		0.49
Reduction factor r₃₀₄		0.74
Nominal ratings
Operating voltage		3.5 ... 30 V
Switching frequency		0 ... 750 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		conducting
Short-circuit protection		pulsing
Voltage drop		&le 3.5 V
Temperature drift		± 15%
Operating current		2 ... 100 mA
Off-state current		0.4 ... 0.6 mA typ. 0.5 mA
Switching state indicator		LED, yellow
Pre-fault indicator		LED, red
Stability control-switch point		0,8 s_r ... 0,9 s_r
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-12GM40-Z5-V1 Pepperl+Fuchs

Каталожный номер: 121012

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm ( -25 ... 70 °C (-13 ... 158 °F) ) 0 ... 6.08 mm ( -40 ... -25 °C (-40 ... -13 °F) )
Reduction factor r_Al		0.49
Reduction factor r_Cu		0.49
Reduction factor r₃₀₄		0.74
Nominal ratings
Operating voltage		3.5 ... 30 V
Switching frequency		0 ... 750 Hz
Reverse polarity protection		conducting
Short-circuit protection		pulsing
Voltage drop		&le 3.5 V
Temperature drift		± 15%
Operating current		2 ... 100 mA
Off-state current		0.4 ... 0.6 mA typ. 0.5 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1930 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-12GM40-Z7-V1 Pepperl+Fuchs

Каталожный номер: 180847

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.49
Reduction factor r_Cu		0.49
Reduction factor r₃₀₄		0.74
Nominal ratings
Operating voltage		3.5 ... 30 V
Switching frequency		0 ... 750 Hz
Hysteresis		typ. 3 %
Reverse polarity protection		conducting
Short-circuit protection		pulsing
Voltage drop		&le 3.5 V
Temperature drift		± 15%
Operating current		2 ... 100 mA
Off-state current		0.4 ... 0.6 mA typ. 0.5 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GK40-N0 Pepperl+Fuchs

Каталожный номер: 181118

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		8 mm
Installation		non-flush
Assured operating distance		0 ... 6.48 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.7
Nominal ratings
Nominal voltage		8.2 V (R_i approx. 1 k&Omega)
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		2040 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
Approvals and certificates
FM approval
	Control drawing	116-0165
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.75 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67
Cable
	Bending radius	> 10 x cable diameter
General information
Use in the hazardous area		see instruction manuals
	Category	2G 1D

Индуктивный датчик Inductive sensor NCN8-18GM40-N0-10M Pepperl+Fuchs

Каталожный номер: 181117

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		8 mm
Installation		non-flush
Assured operating distance		0 ... 6.48 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.42
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.72
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		2040 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
Approvals and certificates
FM approval
	Control drawing	116-0165
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		cable PVC , 10 m
Core cross-section		0.75 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67
Cable
	Bending radius	> 10 x cable diameter
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 1D

Индуктивный датчик Inductive sensor NCN8-18GM40-Z0 Pepperl+Fuchs

Каталожный номер: 89260

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.5 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.44
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		2-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		1739 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GM40-Z0-V1 Pepperl+Fuchs

Каталожный номер: 126072

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.5 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.44
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		2-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		1739 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GM40-Z1 Pepperl+Fuchs

Каталожный номер: 89264

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.5 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.44
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		all direction LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GM40-Z1-V1 Pepperl+Fuchs

Каталожный номер: 89265

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.5 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.44
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		2-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		Multihole-LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GM60-B3B-V1 Pepperl+Fuchs

Каталожный номер: 230829

General specifications
Switching function		Normally open/closed (NO/NC) programmable
Output type		AS-Interface
Rated operating distance		8 mm
Installation		non-flush
Assured operating distance		0 ... 6.48 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.42
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.72
Slave type		A/B slave
AS-Interface specification		V3.0
Required master specification		&ge V2.1
Output type		2-wire
Nominal ratings
Operating voltage		26.5 ... 31.9 V via AS-i bus system
Switching frequency		0 ... 100 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Voltage drop at I_L
	Voltage drop I_L = 20mA, switching element on	3.4 ... 5 V typ. 4.3 V
Operating voltage indicator		dual-LED, green
Switching state indicator		dual-LED, yellow/red
Error indicator		dual-LED, red
Functional safety related parameters
MTTF_d		926 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	Electromagnetic compatibility	EN 50295:1999-10
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GM60-Z0-15M-Y805778 Pepperl+Fuchs

Каталожный номер: 805778

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.44
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		2-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		1739 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 15 m
Core cross-section		0.34 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN8-18GM60-Z0-Y245666 Pepperl+Fuchs

Каталожный номер: 245666

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		non-flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Actual operating distance		7.2 ... 8.8 mm typ. 8 mm
Reduction factor r_Al		0.44
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		2-wire
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 300 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		1739 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 15 m
Core cross-section		0.34 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NEB12-18GM50-E0-V1 Pepperl+Fuchs

Каталожный номер: 231729

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		12 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 9.72 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 36 mm x 36 mm x 1 mm
Reduction factor r_Al		0.26
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.63
Reduction factor r_Brass		0.33
Nominal ratings
Installation conditions
	A	in steel 1.0037 (St37): 4 mm
	B	14 mm
	C	36 mm
	F	36 mm
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Hysteresis		0.12 ... 1.8 mm
Reverse polarity protection		yes
Short-circuit protection		pulsing
Overload resistance		yes
Wire breakage protection		yes
Inductive overvoltage protection		yes
Surge suppression		yes
Ripple		10 %
Voltage drop		&le 2 V
Repeat accuracy		0.6 mm
Operating current		0 ... 200 mA
Off-state current		&le 10 µA
No-load supply current		&le 11 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1940 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67
Mass		50 g

Индуктивный датчик Inductive sensor NEB12-18GM50-E1-V1 Pepperl+Fuchs

Каталожный номер: 231730

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		12 mm
Installation		quasi flush
Output polarity		DC
Assured operating distance		0 ... 9.72 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 36 mm x 36 mm x 1 mm
Reduction factor r_Al		0.26
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.63
Reduction factor r_Brass		0.33
Nominal ratings
Installation conditions
	A	in steel 1.0037 (St37): 4 mm
	B	14 mm
	C	36 mm
	F	36 mm
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Hysteresis		0.12 ... 1.8 mm
Reverse polarity protection		yes
Short-circuit protection		pulsing
Overload resistance		yes
Wire breakage protection		yes
Inductive overvoltage protection		yes
Surge suppression		yes
Ripple		10 %
Voltage drop		&le 2 V
Repeat accuracy		0.6 mm
Operating current		0 ... 200 mA
Off-state current		&le 10 µA
No-load supply current		&le 11 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		2650 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67
Mass		50 g

Pepperl+Fuchs — ориентир в промышленной автоматизации и взрывозащите

Pepperl+Fuchs — немецкий бренд с более чем 75-летней историей инженерного превосходства. Основанная в 1945 году в Мангейме, компания стала пионером бесконтактных датчиков и одним из мировых лидеров в области intrinsically safe решений для опасных сред. Сегодня Pepperl+Fuchs объединяет два направления — Factory Automation и Process Automation — предлагая датчики, интерфейсную электронику, системы взрывозащиты и HMI, которые повышают надежность, безопасность и эффективность производственных процессов.

Ключевые преимущества Pepperl+Fuchs

Инженерное качество: стабильные измерения, высокая повторяемость и минимальные ошибки в жестких условиях эксплуатации.
Безопасность и соответствие: решения с сертификатами ATEX, IECEx, UL и соответствием SIL/PL для критически важных применений.
Готовность к IIoT: поддержка IO-Link, AS-Interface, промышленного Ethernet и современных протоколов для прозрачности данных и предиктивного обслуживания.
Устойчивость к среде: широкий температурный диапазон, стойкость к вибрациям, влаге, пыли и химическим воздействиям (включая IP-защиту).
Совместимость и интеграция: бесшовная работа с ведущими ПЛК и системами управления, унифицированные интерфейсы и аксессуары.
Глобальная поддержка: доступность документации, сервисной сети и запасных частей для надежной долгосрочной эксплуатации.

Продуктовые направления

Датчики и системы распознавания: индуктивные, емкостные, магнитные, ультразвуковые и фотоэлектрические датчики; датчики расстояния, уплотнения контуров и позиционирования; энкодеры, 2D-ридеры и сканеры кода, RFID (HF/UHF), а также интеллектуальные решения с IO-Link. Для задач объемного контроля — лидарные сенсоры и визион-системы.
Интерфейсная техника и искробезопасность: гальванические изоляторы и барьеры (K-System, H-System, Zener), модули ввода/вывода, защита от перенапряжений, источники питания и диагностика шины FieldConnex для Foundation Fieldbus и PROFIBUS PA.
Оборудование для взрывоопасных зон: корпуса и клеммные коробки Ex e/Ex d из нержавеющей стали, алюминия и GRP; станции управления; системы продувки и наддува Bebco EPS; HMI и операторские панели для зон 1/21 и 2/22; мобильные устройства ecom для безопасной работы на площадках.
Связь и подключение: мастера и хабы IO-Link, компоненты AS-Interface, распределительные блоки, коннекторы и кабельная арматура для быстрого и чистого монтажа.
Функциональная безопасность: датчики и модули с подтвержденными уровнями SIL/PL, включая решения AS-i Safety at Work для защиты персонала и оборудования.

Области применения

Решения Pepperl+Fuchs используются в автомобильной промышленности, машиностроении, пищевой и фармацевтической отраслях, логистике и складской автоматизации, а также в нефтегазовом, химическом и горнодобывающем секторах, на объектах энергетики, водоснабжения и очистки стоков. Бренд одинаково эффективен для модернизации отдельных участков и для комплексной автоматизации линий и установок.

Почему это выгодно

Минимум простоев: надежная диагностика и предсказуемое обслуживание снижают незапланированные остановки.
Точность и качество: стабильные показания повышают выпуск и уменьшают брак.
Масштабируемость: широкий ассортимент позволяет развивать систему без смены платформы.
Долгий жизненный цикл: продуманная номенклатура и преемственность серий упрощают поставки и ремонт.
Полный комплект: от датчика и интерфейсных модулей до взрывозащищенных корпусов и операторских панелей.

Как выбрать решение Pepperl+Fuchs

Определите среду (включая наличие взрывоопасных зон), необходимые интерфейсы и уровень безопасности, диапазон измерений и точность, а также условия монтажа. Сверьте каталожные номера с требуемыми сертификатами и аксессуарами. При сложных задачах стоит привлечь инженера для подбора комплекта устройств с учетом специфики технологического процесса.

Pepperl+Fuchs — это инвестиция в надежность, безопасность и предсказуемые результаты. Выбирайте оригинальные решения бренда для уверенной работы оборудования сегодня и готовности к задачам завтрашнего дня.