Купить Pepperl+Fuchs в интернет-магазине Zipstore.ru

Компонент аналогового выхода HART Output Isolator LB4106A Pepperl+Fuchs

Каталожный номер: 254729

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 26 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB10-F17-E2-3M-Y296087 Pepperl+Fuchs

Каталожный номер: 296087

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		10 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 8.1 mm
Actual operating distance		9 ... 11 mm typ. 10 mm
Reduction factor r_Al		0.36
Reduction factor r_Cu		0.31
Reduction factor r₃₀₄		0.67
Output type		3-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 1000 Hz
Hysteresis		1 ... 10 typ. 6 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2.8 V
Operating current		0 ... 100 mA
No-load supply current		10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1881 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.14 mm²
Housing material		PMMA
Sensing face		PMMA
Degree of protection		IP67

Компонент аналогового выхода HART Output Isolator with Shutdown Input LB4106C Pepperl+Fuchs

Каталожный номер: 254730

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 26 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода Universal Input/Output (HART) LB7004A Pepperl+Fuchs

Каталожный номер: 254846

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB10-F17-E3 Pepperl+Fuchs

Каталожный номер: 296086

General specifications
Switching function		Normally closed (NC)
Output type		PNP
Rated operating distance		10 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 8.1 mm
Actual operating distance		9 ... 11 mm typ. 10 mm
Reduction factor r_Al		0.36
Reduction factor r_Cu		0.31
Reduction factor r₃₀₄		0.67
Output type		3-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 1000 Hz
Hysteresis		1 ... 10 typ. 6 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2.8 V
Operating current		0 ... 100 mA
No-load supply current		10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1935 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.14 mm²
Housing material		PMMA
Sensing face		PMMA
Degree of protection		IP67

Компонент аналогового выхода Universal Input/Output (HART) LB7104A Pepperl+Fuchs

Каталожный номер: 254847

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006 EN 50303:2000
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового выхода Digital Output with Shutdown Input LB6108A Pepperl+Fuchs

Каталожный номер: 541996

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		2.2 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		8
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 2- channel II: 3+, 4- channel III: 5+, 6- channel IV: 7+, 8- channel V: 9+, 10- channel VI: 11+, 12- channel VII: 13+, 14- channel VIII: 15+, 16-
Current limit		8 mA
Open loop voltage		20 V
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.33 mA
	Short-circuit	< 300 &Omega
	Open-circuit	> 50 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		LED green: supply LED red: line fault , communication error red flashing
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 160 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (2) G [Ex ib] IIC II (2) D [Ex ib] IIIC
Output
	Voltage	28 V
	Current	13.5 mA
	Power	376 mW (characteristic curve rectangular type)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PF 08 CERT 1234 X PTB 03 ATEX 2042
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ib Gb] IIC T4 Gc [Ex ib Db] IIIC
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB15-30GKK-WO Pepperl+Fuchs

Каталожный номер: 802848

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		15 mm
Installation		flush
Output polarity		AC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.33
Reduction factor r_Cu		0.28
Reduction factor r₃₀₄		0.82
Nominal ratings
Operating voltage		20 ... 250 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 5 %
Short-circuit protection		no
Voltage drop		&le 8 V
Momentary current (20 ms, 0.1 Hz)		0 ... 1600 mA
Operating current		1.5 ... 200 mA
No-load supply current		&le 1.7 mA
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		terminal compartment
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 0.3 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Компонент цифрового выхода Digital Output with Position Feedback LB2016E Pepperl+Fuchs

Каталожный номер: 281971

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		1.3 W
Power consumption		1.8 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		23 V
Current limit		50 mA
Internal resistor		258 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (O: output, I1: input 1, I2: input 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0035X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Input
	Voltage	10 V
	Current	13 mA
	Power	33 mW (linear characteristic)
	Internal capacitance	1.2 nF
	Internal inductance	0 mH
Output
	Voltage	24.2 V
	Current	108 mA
	Power	654 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0035X

Компонент цифрового выхода Digital Output with Position Feedback LB2017E Pepperl+Fuchs

Каталожный номер: 281972

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		1.3 W
Power consumption		1.8 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		16.5 V
Current limit		50 mA
Internal resistor		131 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (O: output, I1: input 1, I2: input 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0035X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Input
	Voltage	10 V
	Current	13 mA
	Power	33 mW (linear characteristic)
	Internal capacitance	1.2 nF
	Internal inductance	0 mH
Output
	Voltage	17.8 V
	Current	162 mA
	Power	721 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0035X

Компонент цифрового выхода Digital Output with Position Feedback LB2116E Pepperl+Fuchs

Каталожный номер: 263859

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		1.3 W
Power consumption		1.8 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		23 V
Current limit		50 mA
Internal resistor		258 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (O: output, I1: input 1, I2: input 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0025X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc II (1) D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Input
	Voltage	10 V
	Current	13 mA
	Power	33 mW (linear characteristic)
	Internal capacitance	1.2 nF
	Internal inductance	0 mH
Output
	Voltage	24.2 V
	Current	108 mA
	Power	654 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0025X

Индуктивный датчик Inductive sensor NBB15-30GKK-WS Pepperl+Fuchs

Каталожный номер: 802849

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		15 mm
Installation		flush
Output polarity		AC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.33
Reduction factor r_Cu		0.28
Reduction factor r₃₀₄		0.82
Nominal ratings
Operating voltage		20 ... 250 V
Switching frequency		0 ... 20 Hz
Hysteresis		typ. 5 %
Short-circuit protection		no
Voltage drop		&le 8 V
Momentary current (20 ms, 0.1 Hz)		0 ... 1600 mA
Operating current		1.5 ... 200 mA
No-load supply current		&le 1.7 mA
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		terminal compartment
Core cross-section		up to 2.5 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67
Note		¹⁾ In the temperature range below 0 °C, permissible operating voltage U_b 80...253 V Safety fuse &le 0.3 A (quick-blow) according to IEC 60127-2 Sheet 1 Recommendation: after a short circuit, check that the device is functioning correctly.

Компонент цифрового выхода Digital Output with Position Feedback LB2117E Pepperl+Fuchs

Каталожный номер: 263863

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		1.3 W
Power consumption		1.8 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		16.5 V
Current limit		50 mA
Internal resistor		131 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (O: output, I1: input 1, I2: input 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0025X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc II (1) D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Input
	Voltage	10 V
	Current	13 mA
	Power	33 mW (linear characteristic)
	Internal capacitance	1.2 nF
	Internal inductance	0 mH
Output
	Voltage	17.8 V
	Current	162 mA
	Power	751 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0025X

Компонент цифрового выхода Digital Output with Shutdown Input LB6008A Pepperl+Fuchs

Каталожный номер: 541993

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		2.2 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		8
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 2- channel II: 3+, 4- channel III: 5+, 6- channel IV: 7+, 8- channel V: 9+, 10- channel VI: 11+, 12- channel VII: 13+, 14- channel VIII: 15+, 16-
Current limit		8 mA
Open loop voltage		20 V
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.33 mA
	Short-circuit	< 300 &Omega
	Open-circuit	> 50 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		LED green: supply LED red: line fault , red flashing: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 160 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Output
	Voltage	28 V
	Current	13.5 mA
	Power	376 mW
	Internal capacitance	3.6 nF
	Internal inductance	0 mH
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		PF 08 CERT 1234 X
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового выхода Digital Output with Shutdown Input LB6016E Pepperl+Fuchs

Каталожный номер: 281973

Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		2
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4/5/6/8- channel II: 7+, 4/5/6/8-
Current limit		40 mA both channels parallel 80 mA
Internal resistor		258 &Omega , both channels parallel 129 &Omega
Open loop voltage		23 V , both channels parallel 23 V
Line fault detection		can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0035X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Output
	Voltage	24.2 V
	Current	108 mA
	Power	654 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Output (both channels parallel)
	Voltage	24.2 V
	Current	216 mA
	Power	1307 mW
	Internal capacitance	24 nF
	Internal inductance	0 mH
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0035X

Индуктивный датчик Inductive sensor NBB15-30GM30-E2 Pepperl+Fuchs

Каталожный номер: 87749

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		2090 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Компонент цифрового выхода Digital Output with Shutdown Input LB6017E Pepperl+Fuchs

Каталожный номер: 281974

Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		2.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		2
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4/5/6/8- channel II: 7+, 4/5/6/8-
Current limit		50 mA both channels parallel 100 mA
Internal resistor		131 &Omega , both channels parallel 66 &Omega
Open loop voltage		16.5 V , both channels parallel 16.5 V
Line fault detection		can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0035X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Output
	Voltage	17.8 V
	Current	162 mA
	Power	721 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Output (both channels parallel)
	Voltage	17.8 V
	Current	324 mA
	Power	1442 mW
	Internal capacitance	24 nF
	Internal inductance	0 mH
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0035X

Компонент цифрового выхода Digital Output with Shutdown Input LB6108C Pepperl+Fuchs

Каталожный номер: 542156

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		2.2 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		8
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 2- channel II: 3+, 4- channel III: 5+, 6- channel IV: 7+, 8- channel V: 9+, 10- channel VI: 11+, 12- channel VII: 13+, 14- channel VIII: 15+, 16-
Current limit		5.2 mA
Open loop voltage		21.6 V
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.33 mA
	Short-circuit	< 300 &Omega
	Open-circuit	> 50 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		LED green: supply LED red: line fault , communication error red flashing
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 160 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (2) G [Ex ib] IIC II (2) D [Ex ib] IIIC
Output
	Voltage	30 V
	Current	13.5 mA
	Power	404 mW (characteristic curve rectangular type)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PF 08 CERT 1234 X PTB 03 ATEX 2042
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ib Gb] IIC T4 Gc [Ex ib Db] IIIC
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB15-30GM30-E2-V1 Pepperl+Fuchs

Каталожный номер: 87747

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm ( -25 ... 70 °C (-13 ... 158 °F) ) 0 ... 11.4 mm ( -40 ... -25 °C (-40 ... -13 °F) )
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		2090 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Компонент цифрового выхода Digital Output with Shutdown Input LB6116E Pepperl+Fuchs

Каталожный номер: 263862

Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		2
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4/5/6/8- channel II: 7+, 4/5/6/8-
Current limit		40 mA both channels parallel 80 mA
Internal resistor		258 &Omega , both channels parallel 129 &Omega
Open loop voltage		23 V , both channels parallel 23 V
Line fault detection		can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0025X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc II (1) D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Output
	Voltage	24.2 V
	Current	108 mA
	Power	654 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Output (both channels parallel)
	Voltage	24.2 V
	Current	216 mA
	Power	1307 mW
	Internal capacitance	24 nF
	Internal inductance	0 mH
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0025X

Компонент цифрового выхода Digital Output with Shutdown Input LB6117E Pepperl+Fuchs

Каталожный номер: 263864

Supply
Connection		backplane bus
Rated voltage		Use only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		2.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		2
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4/5/6/8- channel II: 7+, 4/5/6/8-
Current limit		50 mA both channels parallel 100 mA
Internal resistor		131 &Omega , both channels parallel 66 &Omega
Open loop voltage		16.5 V , both channels parallel 16.5 V
Line fault detection		can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 &Omega
	Open-circuit	> 10 k&Omega
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		EXA 16 ATEX 0025X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc II (1) D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Output
	Voltage	17.8 V
	Current	162 mA
	Power	721 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Output (both channels parallel)
	Voltage	17.8 V
	Current	324 mA
	Power	1442 mW
	Internal capacitance	24 nF
	Internal inductance	0 mH
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		EXA 16 ATEX 0025X

Индуктивный датчик Inductive sensor NBB15-30GM30-E3 Pepperl+Fuchs

Каталожный номер: 87750

General specifications
Switching function		Normally closed (NC)
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		2090 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Компонент цифрового выхода Universal Input/Output (HART) LB7004A Pepperl+Fuchs

Каталожный номер: 254846

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового выхода Universal Input/Output (HART) LB7104A Pepperl+Fuchs

Каталожный номер: 254847

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006 EN 50303:2000
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB15-30GM30-E3-V1 Pepperl+Fuchs

Каталожный номер: 87748

General specifications
Switching function		Normally closed (NC)
Output type		PNP
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 150 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		2090 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP67

Компонент цифрового выхода Digital Output with Position Feedback LB2002A Pepperl+Fuchs

Каталожный номер: 541938

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		1.8 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		24 V
Current limit		75 mA
Internal resistor		210 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 110 &Omega
	Open-circuit	> 1.2 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		LED green: supply LED red: line fault, per channel LED yellow: signal (status), per channel
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Input
	Voltage	14 V
	Current	16 mA
	Power	55 mW (linear characteristic)
	Internal capacitance	1.65 µF
	Internal inductance	0 mH
Output
	Voltage	27.8 V
	Current	183 mA
	Power	1270 mW
	Internal capacitance	3.3 µF
	Internal inductance	0 mH
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIB T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		PF 08 CERT 1234 X
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового выхода Digital Output with Position Feedback LB2101A Pepperl+Fuchs

Каталожный номер: 541940

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.3 W
Power consumption		1.6 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		22 V
Current limit		50 mA
Internal resistor		315 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 20 &Omega
	Open-circuit	> 2 k&Omega
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		LED green: supply LED red: line fault, per channel LED yellow: signal (status), per channel
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIC II (1) D [Ex ia] IIIC
Input
	Voltage	14 V
	Current	16 mA
	Power	55 mW (linear characteristic)
	Internal capacitance	1.65 µF
	Internal inductance	0 mH
Output
	Voltage	24.9 V
	Current	91 mA
	Power	558 mW
	Internal capacitance	1.65 µF
	Internal inductance	0 mH
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PF 08 CERT 1234 X PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0321
	Approved for	cUL (Canada): CL I Zn. 2 IIC IS circuits for CL I Zn. 0 IIC ULus (USA): CL I Div. 2 Grp. A, B, C, D IS circuits for CL I, II, III Div. 1 Grp. A, B, C, D, E, F, G
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB15-30GM35-A0 Pepperl+Fuchs

Каталожный номер: 293453-0019

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1000 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 1.8 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1733 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67
Mass		126 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Компонент цифрового выхода Digital Output with Position Feedback LB2102A Pepperl+Fuchs

Каталожный номер: 541942

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.8 W
Power consumption		2.4 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 2+, 5- channel II: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Digital output
Number of channels		1
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4-
Open loop voltage		24 V
Current limit		75 mA
Internal resistor		210 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 110 &Omega
	Open-circuit	> 1.2 k&Omega
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		LED green: supply LED red: line fault, per channel LED yellow: signal (status), per channel
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIB II (1) D [Ex ia] IIIC
Input
	Voltage	14 V
	Current	16 mA
	Power	55 mW (linear characteristic)
	Internal capacitance	1.65 µF
	Internal inductance	0 mH
Output
	Voltage	27.8 V
	Current	183 mA
	Power	1270 mW
	Internal capacitance	1.65 µF
	Internal inductance	0 mH
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIB T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PF 08 CERT 1234 X PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0321
	Approved for	cUL (Canada): CL I Zn. 2 IIC IS circuits for CL I Zn. 0 IIC ULus (USA): CL I Div. 2 Grp. A, B, C, D IS circuits for CL I, II, III Div. 1 Grp. A, B, C, D, E, F, G
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB15-30GM35-A0-M1 Pepperl+Fuchs

Каталожный номер: 293454-0076

General specifications
Switching function		complementary
Output type		NPN
Rated operating distance		15 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 12.15 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 45 mm x 45 mm x 1 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Output type		4-wire
Nominal ratings
Operating voltage		7 ... 30 V
Switching frequency		0 ... 1400 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 4 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1494 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP68 / IP69K
Mass		121 g
General information
Scope of delivery		2 self locking nuts in scope of delivery

Запасные части Pepperl+Fuchs

Каталог запчастей Pepperl+Fuchs

Купить запчасти для Pepperl+Fuchs оптом и в розницу

Техподдержка