Запасные части Pepperl+Fuchs

Сортировать по: Название Цена Блоки Таблица

Индуктивный датчик Inductive sensor NBB2-12GM50-E0 Pepperl+Fuchs

Каталожный номер: 87761

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1600 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, Panel Mount, Pushbutton PMP.PZ1.C.20 Pepperl+Fuchs

Каталожный номер: 297341

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		pushbutton
	Color	choice of red, green, amber, white, blue, black
	Contact configuration	2x NO
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
	Operator action	momentary
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	15.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	128 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Potentiometer PMR.R2.P.0.5K Pepperl+Fuchs

Каталожный номер: 297367

Electrical specifications
Operating voltage		200 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		potentiometer
	Color	black
	Range	0 ... 0.5 k&Omega
	Operator action	continuously rotary
	Labeling	0 ... 10
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB2-12GM50-E0-5M Pepperl+Fuchs

Каталожный номер: 83093

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1600 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 5 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, Panel Mount, Potentiometer PMR.R2.P.10K Pepperl+Fuchs

Каталожный номер: 297370

Electrical specifications
Operating voltage		200 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		potentiometer
	Color	black
	Range	0 ... 10 k&Omega
	Operator action	continuously rotary
	Labeling	0 ... 10
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Potentiometer PMR.R2.P.1K Pepperl+Fuchs

Каталожный номер: 297368

Electrical specifications
Operating voltage		200 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		potentiometer
	Color	black
	Range	0 ... 1 k&Omega
	Operator action	continuously rotary
	Labeling	0 ... 10
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB2-12GM50-E0-C-V1 Pepperl+Fuchs

Каталожный номер: 906037

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 1500 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		Multihole-LED, yellow
Mag. Field strength, AC fields		200 mT
Mag. Field strength, DC fields		200 mT
Functional safety related parameters
MTTF_d		2060 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		Brass, PTFE coated
Sensing face		PPS
Housing diameter		12 mm
Degree of protection		IP67

Модуль управления Control Unit Ex e, Panel Mount, Potentiometer PMR.R2.P.2K Pepperl+Fuchs

Каталожный номер: 297369

Electrical specifications
Operating voltage		200 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		potentiometer
	Color	black
	Range	0 ... 2 k&Omega
	Operator action	continuously rotary
	Labeling	0 ... 10
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Key Switch PMS.K6.C.11 Pepperl+Fuchs

Каталожный номер: 297360

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		key switch
	Color	black / silver
	Contact configuration	1x NO / 1x NC
	Switching configuration	2 position changeover with left OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage
	Lockable	yes
	Labeling	0 - I
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	33.3 mm (H)
	Width across flats	24 mm (SW1)
	Total length	145.8 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB2-12GM50-E0-V1 Pepperl+Fuchs

Каталожный номер: 87762

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA
No-load supply current		&le 17 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		1600 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, Panel Mount, Key Switch PMS.K6.C.20 Pepperl+Fuchs

Каталожный номер: 297359

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		key switch
	Color	black / silver
	Contact configuration	2x NO
	Switching configuration	2 position changeover with left OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage
	Lockable	yes
	Labeling	0 - I
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	33.3 mm (H)
	Width across flats	24 mm (SW1)
	Total length	145.8 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Key Switch PMS.K8.C.20 Pepperl+Fuchs

Каталожный номер: 297361

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		key switch
	Color	black / silver
	Contact configuration	2x NO
	Switching configuration	3 position changeover with center OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage - engage
	Lockable	yes
	Labeling	l - 0 - ll
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	33.3 mm (H)
	Width across flats	24 mm (SW1)
	Total length	145.8 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB2-12GM50-E0-Y263157 Pepperl+Fuchs

Каталожный номер: 263157

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1600 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, Panel Mount, Control Switch PMS.N6.C.20 Pepperl+Fuchs

Каталожный номер: 297355

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		control switch, small
	Color	black
	Contact configuration	2x NO
	Switching configuration	2 position changeover with left OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage
	Labeling	0 - l
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Control Switch PMS.N7.C.11 Pepperl+Fuchs

Каталожный номер: 297356

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		control switch, small
	Color	black
	Contact configuration	1x NO / 1x NC
	Switching configuration	2 position changeover with left OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage
	Labeling	I - II
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB2-12GM50-E1 Pepperl+Fuchs

Каталожный номер: 87769

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1600 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, Panel Mount, Control Switch PMS.N8.C.20 Pepperl+Fuchs

Каталожный номер: 297357

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		control switch, small
	Color	black
	Contact configuration	2x NO
	Switching configuration	3 position changeover with center OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage - engage
	Labeling	l - 0 - ll
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Control Switch PMS.N9.C.11 Pepperl+Fuchs

Каталожный номер: 297358

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		control switch, small
	Color	black
	Contact configuration	1x NO / 1x NC
	Switching configuration	3 position changeover with center OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage - engage
	Labeling	0 - I - II
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	30.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	143.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB2-12GM50-E1-V1 Pepperl+Fuchs

Каталожный номер: 87770

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 17 mA
Switching state indicator		Multihole-LED, yellow
Functional safety related parameters
MTTF_d		1600 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, GRP, Pushbutton LCP1.DMMX.B.1 Pepperl+Fuchs

Каталожный номер: 265369

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		double pushbutton
	Color	red / green
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	0 - I
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Emergency Stop LCP1.ERMX.B.1 Pepperl+Fuchs

Каталожный номер: 265365

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		mushroom button
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	latching , pull to release
	Labeling	EMERGENCY STOP / NOT AUS
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		142 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Индуктивный датчик Inductive sensor NBB2-12GM50-E2 Pepperl+Fuchs

Каталожный номер: 87763

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1060 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, GRP, Emergency Stop LCP1.ERMX.F.1 Pepperl+Fuchs

Каталожный номер: 273234

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		mushroom button
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	latching , pull to release
	Labeling	EMERGENCY STOP / NOT AUS
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		142 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Emergency Stop LCP1.ERMZA.B.1 Pepperl+Fuchs

Каталожный номер: 265366

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		mushroom button
	Color	red
	Shroud	plastic lid
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	latching , pull to release
	Labeling	EMERGENCY STOP / NOT AUS
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		148 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Индуктивный датчик Inductive sensor NBB2-12GM50-E2-25M Pepperl+Fuchs

Каталожный номер: 240277

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		990 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR black , 25 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, GRP, Emergency Stop LCP1.ERMZP.B.1 Pepperl+Fuchs

Каталожный номер: 265367

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		mushroom button
	Color	red
	Shroud	plastic
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	latching , pull to release
	Lockable	padlockable via shroud
	Labeling	EMERGENCY STOP / NOT AUS
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		145 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Illuminated Pushbutton LCP1.IGIX.F.1 Pepperl+Fuchs

Каталожный номер: 293224

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		illuminated pushbutton
	Color	green
	Contact configuration	1x NO
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	1
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Индуктивный датчик Inductive sensor NBB2-12GM50-E2-3M Pepperl+Fuchs

Каталожный номер: 806489

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		2 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 1.62 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.7
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 1500 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 17 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		990 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR black , 3 m
Core cross-section		0.14 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		12 mm
Degree of protection		IP67
General information
Scope of delivery		2 self locking nuts in scope of delivery

Модуль управления Control Unit Ex e, GRP, Illuminated Pushbutton LCP1.IRJX.F.1 Pepperl+Fuchs

Каталожный номер: 293223

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		illuminated pushbutton
	Color	red
	Contact configuration	1x NC
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	1
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Emergency Stop LCP1.JRMX.B.1 Pepperl+Fuchs

Каталожный номер: 265368

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		mushroom button
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	latching , key release
	Lockable	yes
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		133 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Компания Zipstore.ru поставляет оптом и в розницу запчасти Pepperl+Fuchs.

Каталог запчастей Pepperl+Fuchs

В каталоге сайта представлено 13440 запчастей Pepperl+Fuchs. Также вы можете приобрести опции и аксессуары для расширения функциональных возможностей, транспортировки и эксплуатации оборудования. Запчасти в каталоге могут иметь полное название, каталожный номер, фотографию, краткое описание, а также модели принтеров, с которыми они совместимы.

Купить запчасти для Pepperl+Fuchs оптом и в розницу

Для оформления заказа вы можете воспользоваться одним из следующих способов:

отправить заявку по электронной почте info@zipstore.ru
связаться с нашим менеджером при помощи формы обратной связи
с помощью активной кнопки "Купить" в каталоге товаров или в конкретном товаре
с помощью формы "Купить в 1 клик" в конкретном товаре

Мы осуществляем поставки запчастей Pepperl+Fuchs во все города России, а также в Республику Беларусь, Казахстан и другие страны СНГ.

Продажа осуществляется за наличный и безналичный расчет. На сайте указаны розничные цены в рублях и долларах, с учетом НДС. Чтобы узнать оптовые цены на запчасти Pepperl+Fuchs, нужно отправить запрос по электронной почте. Подробнее о способах доставки и оплаты можно узнать в разделе сайта «Оплата и доставка». В разделе «%Скидки и акции» Вы можете найти наиболее выгодные предложения по продаже запчастей, а также сезонные скидки и акции.

Техподдержка

При возникновении вопросов по обслуживанию, эксплуатации, ремонту Pepperl+Fuchs, Вы можете проконсультироваться со специалистами на форуме сайта.