Запасные части Pepperl+Fuchs

Сортировать по: Название Цена Блоки Таблица

Индуктивный датчик Inductive sensor NBB8-18GM60-A2-V1-3G-3D Pepperl+Fuchs

Каталожный номер: 212062

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		8 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		4-wire
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 500 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 25 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67
General information
Use in the hazardous area		see instruction manuals
	Category	3G 3D

Модуль управления Control Unit Ex e, GRP, Pushbutton LCP1.PGMX.F.1 Pepperl+Fuchs

Каталожный номер: 293222

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		pushbutton
	Color	green
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	I
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Pushbutton LCP1.PRMX.A.1 Pepperl+Fuchs

Каталожный номер: 305055

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		pushbutton
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	0
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Pushbutton LCP1.PRMX.F.1 Pepperl+Fuchs

Каталожный номер: 293221

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		pushbutton
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	0
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Индуктивный датчик Inductive sensor NBB8-18GM60-B3-V1 Pepperl+Fuchs

Каталожный номер: 226335

General specifications
Switching function		Normally open/closed (NO/NC) programmable
Output type		AS-Interface
Rated operating distance		8 mm
Installation		flush
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.5
Slave type		Standard slave
AS-Interface specification		V2.1
Required master specification		&ge V2.0
Nominal ratings
Operating voltage		26.5 ... 31.9 V via AS-i bus system
Switching frequency		0 ... 200 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
No-load supply current		&le 25 mA
Switching state indicator		dual-LED, yellow
Error indicator		dual-LED, red
Functional safety related parameters
MTTF_d		926 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		4-pin, M12 x 1 connector
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Модуль управления Control Unit Ex e, GRP, Control Switch LCP1.S1OX.A.1 Pepperl+Fuchs

Каталожный номер: 305062

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		control switch, large
	Color	black
	Shroud	yes
	Contact configuration	2x NO
	Switching configuration	2 position changeover with left OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage
	Lockable	padlockable in '0'
	Labeling	0 - l
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		131 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, Control Switch LCP1.S1OX.F.1 Pepperl+Fuchs

Каталожный номер: 293233

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		control switch, large
	Color	black
	Shroud	yes
	Contact configuration	2x NO
	Switching configuration	2 position changeover with left OFF
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	engage - engage
	Lockable	padlockable in '0'
	Labeling	0 - l
Mechanical specifications
Height		110 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		131 mm with operators (C1) 125 mm with mounting brackets (K)
Fixing holes distance, height		110 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		1.5 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Индуктивный датчик Inductive sensor NBB8-18GM60-UO Pepperl+Fuchs

Каталожный номер: 198077

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		flush
Output polarity		AC/DC
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		3-wire
Nominal ratings
Operating voltage		20 ... 250 V AC/20 ... 300 V DC
Switching frequency		30 Hz
Hysteresis		3 ... 15 typ. 5 %
Reverse polarity protection		yes
Short-circuit protection		yes
Voltage drop		&le 8 V
Operating current		4 ... 300 mA AC/DC
Off-state current		&le 0.8 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.5 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Модуль управления Control Unit Ex e, GRP, 2 Functions LCP2.PGMX.ERMX.F.1 Pepperl+Fuchs

Каталожный номер: 293241

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		pushbutton
	Color	green
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	I
Function 2		mushroom button
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Operator action	latching , pull to release
	Labeling	EMERGENCY STOP / NOT AUS
Mechanical specifications
Height		220 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		142 mm with operators (C1) 235 mm with mounting brackets (K)
Fixing holes distance, height		220 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		3 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, GRP, 2 Functions LCP2.PGMX.PRMX.F.1 Pepperl+Fuchs

Каталожный номер: 293240

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		pushbutton
	Color	green
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	I
Function 2		pushbutton
	Color	red
	Contact configuration	1x NO / 1x NC
	Usage category	AC12 - 12 ... 250 V AC - 16 A AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 110 V DC - 1 A DC13 - 12 ... 24 V DC - 1A
	Number of poles	2
	Labeling	O
Mechanical specifications
Height		220 mm (A)
Width		110 mm (B)
Depth		101 mm (C)
External dimension		116 mm with operators (C1) 235 mm with mounting brackets (K)
Fixing holes distance, height		220 mm (G)
Fixing holes distance, width		78 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel socket cap head screws
Fixing holes diameter		7 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M25 in face B fitted with polyamide Ex e cable gland
Defined entry area		face B
Material
	Enclosure	carbon loaded, antistatic glass fiber reinforced polyester (GRP)
	Finish	inherent color black
	Seal	one piece solid silicone rubber
Mass		3 kg
Mounting		7 mm slots moulded into base
Grounding		2.5 mm² grounding terminal
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, Stainless Steel, Illuminated Pushbutton LCS1.IGIX.B.1 Pepperl+Fuchs

Каталожный номер: 267116

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		illuminated pushbutton
	Color	green
	Contact configuration	1x NO
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	1
Mechanical specifications
Height		102 mm (A)
Width		116 mm (B)
Depth		85.5 mm (C)
External dimension		100 mm with operators (C1) 92.2 mm with screws (C2) 145 mm with mounting brackets (K)
Fixing holes distance, height		41 mm (G)
Fixing holes distance, width		130 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel hexagon head screws
Fixing holes diameter		6.1 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	1.5 mm 316L, (1.4404) stainless steel
	Finish	electropolished
	Seal	one piece closed cell neoprene
Mass		1.5 kg
Mounting		mouting brackets with 6.1 mm screw holes
Grounding		M6 internal/external brass grounding bolt
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Индуктивный датчик Inductive sensor NBB8-18GM60-UO-V12 Pepperl+Fuchs

Каталожный номер: 198079

General specifications
Switching function		Normally closed (NC)
Output type		Two-wire
Rated operating distance		8 mm
Installation		flush
Output polarity		AC/DC
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		3-wire
Nominal ratings
Operating voltage		20 ... 250 V AC/20 ... 300 V DC
Switching frequency		30 Hz
Hysteresis		3 ... 15 typ. 5 %
Reverse polarity protection		yes
Short-circuit protection		yes
Voltage drop		&le 8 V
Operating current		4 ... 300 mA AC/DC
Off-state current		&le 0.8 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Standard conformity
Standards		IEC / EN 60947-5-2:2004
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector 1/2"-20 UN , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Модуль управления Control Unit Ex e, Stainless Steel, Illuminated Pushbutton LCS1.IRJX.B.1 Pepperl+Fuchs

Каталожный номер: 267115

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
Function		illuminated pushbutton
	Color	red
	Contact configuration	1x NC
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	1
Mechanical specifications
Height		102 mm (A)
Width		116 mm (B)
Depth		85.5 mm (C)
External dimension		100 mm with operators (C1) 92.2 mm with screws (C2) 145 mm with mounting brackets (K)
Fixing holes distance, height		41 mm (G)
Fixing holes distance, width		130 mm (H)
Enclosure cover		fully detachable
Cover fixing		M6 stainless steel hexagon head screws
Fixing holes diameter		6.1 mm (J)
Degree of protection		IP66
Cable entry
	Number of cable entries	1 x M20 in face A fitted with polyamide Ex e stopping plug 1x M20 in face B fitted with polyamide Ex e cable gland
Defined entry area		face A and face B
Material
	Enclosure	1.5 mm 316L, (1.4404) stainless steel
	Finish	electropolished
	Seal	one piece closed cell neoprene
Mass		1.5 kg
Mounting		mouting brackets with 6.1 mm screw holes
Grounding		M6 internal/external brass grounding bolt
Ambient conditions
Ambient temperature		-40 ... 55 °C (-40 ... 131 °F) @ T4 -40 ... 40 °C (-40 ... 104 °F) @ T6
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3009 X
	Marking	II 2 GD Ex db eb mb IIC T* Gb Ex tb IIIC T** °C Db T6/T80 °C @ Ta +40 °C T4/T130 °C @ Ta +55 °C
International approvals
IECEx approval		IECEx CML 16.0008X
EAC approval		TC RU C-DE.GB06.B.00567
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Accessories
Optional accessories		Engraved traffolyte tag label Engraved AISI 316L stainless steel tag label Color in-fill stainless steel tag label

Модуль управления Control Unit Ex e, Panel Mount, Illuminated Pushbutton PMI.IG.I.W.01 Pepperl+Fuchs

Каталожный номер: 297354

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
	Terminal torque	0.8 Nm
Function		illuminated pushbutton
	Color	green
	Contact configuration	1x NC
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	17.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	130 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Illuminated Pushbutton PMI.IG.I.W.10 Pepperl+Fuchs

Каталожный номер: 297353

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
	Terminal torque	0.8 Nm
Function		illuminated pushbutton
	Color	green
	Contact configuration	1x NO
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	17.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	130 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB8-18GM60-US-10M Pepperl+Fuchs

Каталожный номер: 264306

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		flush
Output polarity		AC/DC
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		3-wire
Nominal ratings
Operating voltage		20 ... 250 V AC/20 ... 300 V DC
Switching frequency		30 Hz
Hysteresis		3 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		yes
Voltage drop		&le 8 V
Operating current		4 ... 300 mA AC/DC
Off-state current		&le 0.8 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 10 m
Core cross-section		0.5 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Модуль управления Control Unit Ex e, Panel Mount, Illuminated Pushbutton PMI.IR.I.W.01 Pepperl+Fuchs

Каталожный номер: 297352

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
	Terminal torque	0.8 Nm
Function		illuminated pushbutton
	Color	red
	Contact configuration	1x NC
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	17.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	130 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Illuminated Pushbutton PMI.IR.I.W.10 Pepperl+Fuchs

Каталожный номер: 297351

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2.5 mm²
	Terminal torque	0.8 Nm
Function		illuminated pushbutton
	Color	red
	Contact configuration	1x NO
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	17.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	130 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, LED Indicator PML.LB.L.W.2 Pepperl+Fuchs

Каталожный номер: 297366

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	1.1 Nm
Function		LED indicator
	Color	blue
	Rated operating voltage	12 ... 250 V AC/DC
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	23.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	136.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3106 X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB8-18GM60-US-V12 Pepperl+Fuchs

Каталожный номер: 198078

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		8 mm
Installation		flush
Output polarity		AC/DC
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		3-wire
Nominal ratings
Operating voltage		20 ... 250 V AC/20 ... 300 V DC
Switching frequency		30 Hz
Hysteresis		3 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		yes
Voltage drop		&le 8 V
Operating current		4 ... 300 mA AC/DC
Off-state current		&le 0.8 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector 1/2"-20 UN , 3-pin
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Модуль управления Control Unit Ex e, Panel Mount, LED Indicator PML.LG.L.W.2 Pepperl+Fuchs

Каталожный номер: 297363

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	1.1 Nm
Function		LED indicator
	Color	green
	Rated operating voltage	12 ... 250 V AC/DC
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	23.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	136.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3106 X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, LED Indicator PML.LO.L.W.2 Pepperl+Fuchs

Каталожный номер: 297364

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	1.1 Nm
Function		LED indicator
	Color	amber
	Rated operating voltage	12 ... 250 V AC/DC
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	23.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	136.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3106 X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, LED Indicator PML.LR.L.W.2 Pepperl+Fuchs

Каталожный номер: 297362

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	1.1 Nm
Function		LED indicator
	Color	red
	Rated operating voltage	12 ... 250 V AC/DC
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	23.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	136.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3106 X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive sensor NBB8-18GM70-E2-V94 Pepperl+Fuchs

Каталожный номер: 903598

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		8 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.45
Reduction factor r_Cu		0.4
Reduction factor r₃₀₄		0.7
Output type		3-wire
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 500 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 15 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Connector 7/8 inch-16 UN , 4-pin
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Модуль управления Control Unit Ex e, Panel Mount, LED Indicator PML.LW.L.W.2 Pepperl+Fuchs

Каталожный номер: 297365

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	1.1 Nm
Function		LED indicator
	Color	white
	Rated operating voltage	12 ... 250 V AC/DC
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	23.6 mm (H)
	Width across flats	24 mm (SW1)
	Total length	136.1 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16 ATEX 3106 X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Pushbutton PMP.DZ3.C.02 Pepperl+Fuchs

Каталожный номер: 297349

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		double pushbutton
	Color	choice of red, green, amber, white, blue, black
	Contact configuration	2x NC
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
	Operator action	momentary
	Labeling	various, see features
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	15.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	128 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Модуль управления Control Unit Ex e, Panel Mount, Pushbutton PMP.DZ3.C.11 Pepperl+Fuchs

Каталожный номер: 297348

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		double pushbutton
	Color	choice of red, green, amber, white, blue, black
	Contact configuration	1x NO / 1x NC
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
	Operator action	momentary
	Labeling	various, see features
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	15.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	128 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Индуктивный датчик Inductive analog sensor NBB8-30GM60-I3 Pepperl+Fuchs

Каталожный номер: 282837

General specifications
Output type		Analog current output
Installation		flush
Output polarity		DC
Measurement range		3 ... 8 mm
Output type		3-wire
Nominal ratings
Operating voltage		15 ... 30 V DC
Repeat accuracy		0 ... 200 µm
Recovery time		1 ... 10 ms typ. 5 ms
No-load supply current		&le 12 mA
Analog output
Output type		0 ... 20 mA
Linearity error		&le ± 5 % of full-scale value
Load resistor		&le 500 &Omega
Temperature drift		&le ± 0.15 %/K of the measured value
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.75 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Degree of protection		IP67

Индуктивный датчик Inductive sensor NCN3-F31-B3-V1-K Pepperl+Fuchs

Каталожный номер: 226323

Описание оборудования
Valve positioner and valve control module

Модуль управления Control Unit Ex e, Panel Mount, Pushbutton PMP.DZ3.C.20 Pepperl+Fuchs

Каталожный номер: 297350

Electrical specifications
Operating voltage		250 V max.
Operating current		16 A max.
Terminal capacity		2x 2.5 mm²
	Terminal torque	0.8 Nm
Function		double pushbutton
	Color	choice of red, green, amber, white, blue, black
	Contact configuration	2x NO
	Usage category	AC15 - 12 ... 250 V AC - 10 A DC13 - 12 ... 24 V DC - 1 A
	Number of poles	2
	Operator action	momentary
	Labeling	various, see features
Mechanical specifications
Cable type		non-armored cables
Clamping range		5.5 ... 13 mm (D)
Covering		Protective cover fully detachable
Cover fixing		Phillips head screw
Degree of protection		IP66
Cable entry
	Number of cable entries	1x M20 cable gland in protective cover
Material
	Housing	Polyamide (PA)
	Finish	inherent color black
	Seal	silicone
	Washer gasket	silicone
Mass		150 g max.
Dimensions
	Height	77 mm (A)
	Width	44 mm (B)
	Depth	105 mm (C)
	Actuator head diameter	39 mm (D2)
	Panel wall thickness	1 ... 6 mm (PT)
	Diameter thru-hole	30.6 mm (DT)
	Length outside enclosure	15.5 mm (H)
	Width across flats	24 mm (SW1)
	Total length	128 mm (L)
Tightening torque
	Nut torque at enclosure	2 Nm (SW1)
Mounting		via actuator head
Ambient conditions
Ambient temperature		-40 ... 50 °C (-40 ... 122 °F)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		CML 16ATEX3106X
	Marking	II 2 GD Ex de IIC T6 Gb Ex tb IIIC T80 °C Db
International approvals
IECEx approval		IECEx CML 16.0046X
Conformity
Degree of protection		EN 60529
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Pepperl+Fuchs — ориентир в промышленной автоматизации и взрывозащите

Pepperl+Fuchs — немецкий бренд с более чем 75-летней историей инженерного превосходства. Основанная в 1945 году в Мангейме, компания стала пионером бесконтактных датчиков и одним из мировых лидеров в области intrinsically safe решений для опасных сред. Сегодня Pepperl+Fuchs объединяет два направления — Factory Automation и Process Automation — предлагая датчики, интерфейсную электронику, системы взрывозащиты и HMI, которые повышают надежность, безопасность и эффективность производственных процессов.

Ключевые преимущества Pepperl+Fuchs

Инженерное качество: стабильные измерения, высокая повторяемость и минимальные ошибки в жестких условиях эксплуатации.
Безопасность и соответствие: решения с сертификатами ATEX, IECEx, UL и соответствием SIL/PL для критически важных применений.
Готовность к IIoT: поддержка IO-Link, AS-Interface, промышленного Ethernet и современных протоколов для прозрачности данных и предиктивного обслуживания.
Устойчивость к среде: широкий температурный диапазон, стойкость к вибрациям, влаге, пыли и химическим воздействиям (включая IP-защиту).
Совместимость и интеграция: бесшовная работа с ведущими ПЛК и системами управления, унифицированные интерфейсы и аксессуары.
Глобальная поддержка: доступность документации, сервисной сети и запасных частей для надежной долгосрочной эксплуатации.

Продуктовые направления

Датчики и системы распознавания: индуктивные, емкостные, магнитные, ультразвуковые и фотоэлектрические датчики; датчики расстояния, уплотнения контуров и позиционирования; энкодеры, 2D-ридеры и сканеры кода, RFID (HF/UHF), а также интеллектуальные решения с IO-Link. Для задач объемного контроля — лидарные сенсоры и визион-системы.
Интерфейсная техника и искробезопасность: гальванические изоляторы и барьеры (K-System, H-System, Zener), модули ввода/вывода, защита от перенапряжений, источники питания и диагностика шины FieldConnex для Foundation Fieldbus и PROFIBUS PA.
Оборудование для взрывоопасных зон: корпуса и клеммные коробки Ex e/Ex d из нержавеющей стали, алюминия и GRP; станции управления; системы продувки и наддува Bebco EPS; HMI и операторские панели для зон 1/21 и 2/22; мобильные устройства ecom для безопасной работы на площадках.
Связь и подключение: мастера и хабы IO-Link, компоненты AS-Interface, распределительные блоки, коннекторы и кабельная арматура для быстрого и чистого монтажа.
Функциональная безопасность: датчики и модули с подтвержденными уровнями SIL/PL, включая решения AS-i Safety at Work для защиты персонала и оборудования.

Области применения

Решения Pepperl+Fuchs используются в автомобильной промышленности, машиностроении, пищевой и фармацевтической отраслях, логистике и складской автоматизации, а также в нефтегазовом, химическом и горнодобывающем секторах, на объектах энергетики, водоснабжения и очистки стоков. Бренд одинаково эффективен для модернизации отдельных участков и для комплексной автоматизации линий и установок.

Почему это выгодно

Минимум простоев: надежная диагностика и предсказуемое обслуживание снижают незапланированные остановки.
Точность и качество: стабильные показания повышают выпуск и уменьшают брак.
Масштабируемость: широкий ассортимент позволяет развивать систему без смены платформы.
Долгий жизненный цикл: продуманная номенклатура и преемственность серий упрощают поставки и ремонт.
Полный комплект: от датчика и интерфейсных модулей до взрывозащищенных корпусов и операторских панелей.

Как выбрать решение Pepperl+Fuchs

Определите среду (включая наличие взрывоопасных зон), необходимые интерфейсы и уровень безопасности, диапазон измерений и точность, а также условия монтажа. Сверьте каталожные номера с требуемыми сертификатами и аксессуарами. При сложных задачах стоит привлечь инженера для подбора комплекта устройств с учетом специфики технологического процесса.

Pepperl+Fuchs — это инвестиция в надежность, безопасность и предсказуемые результаты. Выбирайте оригинальные решения бренда для уверенной работы оборудования сегодня и готовности к задачам завтрашнего дня.