Name: Индуктивный датчик Inductive analog sensor NBB5-18GM60-I3-V1 Pepperl+Fuchs
Brand: Pepperl+Fuchs
SKU: 303097

General specifications

Output type

Analog current output

Installation

flush

Output polarity

Measurement range

1 ... 5 mm

Output type

3-wire

Nominal ratings

Operating voltage

10 ... 30 V

Repeat accuracy

0 ... 20 µm

No-load supply current

&le 12 mA

Analog output

Output type

0 ... 20 mA

Linearity error

&le ± 4 % of full-scale value

Load resistor

&le 1000 &Omega

Temperature drift

&le ± 0.1 %/K of the measured value

Approvals and certificates

UL approval

cULus Listed, General Purpose

CSA approval

cCSAus Listed, General Purpose

CCC approval

CCC approval / marking not required for products rated &le36 V

Ambient conditions

Ambient temperature

-25 ... 70 °C (-13 ... 158 °F)

Mechanical specifications

Connection type

Connector M12 x 1 , 4-pin

Housing material

brass, nickel-plated

Sensing face

PBT

Degree of protection

IP67

Клиенты

Покупатели, которые приобрели Индуктивный датчик Inductive analog sensor NBB5-18GM60-I3-V1 Pepperl+Fuchs, также купили

Индуктивный датчик Inductive sensor NBB20-L2-A2-V1 Pepperl+Fuchs

Каталожный номер: 187548

General specifications
Switching function		complementary
Output type		PNP
Rated operating distance		20 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 16.2 mm
Actual operating distance		18 ... 22 mm
Reduction factor r_Al		0.33
Reduction factor r_Cu		0.31
Reduction factor r₃₀₄		0.74
Reduction factor r_Brass		0.41
Nominal ratings
Operating voltage		10 ... 30 V DC
Switching frequency		0 ... 440 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 2 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA
No-load supply current		&le 20 mA
Operating voltage indicator		LED, green
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1230 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
EAC conformity		TR CU 020/2011
Protection class		II
	Rated insulation voltage	253 V
	Rated impulse withstand voltage	4000 V
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 85 °C (-13 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 4-pin
Housing material		PA
Sensing face		PA
Housing diameter
Degree of protection		IP69K
Mass		130 g

Индуктивный датчик Inductive sensor NBB5-18GM40-Z0 Pepperl+Fuchs

Каталожный номер: 88200

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		5 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 4.05 mm
Actual operating distance		4.5 ... 5.5 mm typ. 5 mm
Reduction factor r_Al		0.34
Reduction factor r_Cu		0.31
Reduction factor r₃₀₄		0.72
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 500 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity tolerant
Short-circuit protection		pulsing
Voltage drop		&le 5 V
Operating current		2 ... 100 mA
Lowest operating current		2 mA
Off-state current		0 ... 0.5 mA typ.
Switching state indicator		all direction LED, yellow
Functional safety related parameters
MTTF_d		1870 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		Certified by China Compulsory Certification (CCC)
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		brass, nickel-plated
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP67

Индуктивная система позиционирования Inductive positioning system PMI360-F110-IU-V1 Pepperl+Fuchs

Каталожный номер: 191141

General specifications
Switching element function		analog, current or voltage output
Object distance		max. 6 mm
Measurement range		0 ... 360 mm
Nominal ratings
Operating voltage		18 ... 30 V DC
Reverse polarity protection		reverse polarity protected
Linearity error		± 0.4 mm
Repeat accuracy		± 0.2 mm
Resolution		360 µm
Temperature drift		± 0.5 mm (-25 °C ... 70 °C)
No-load supply current		&le 40 mA
Operating voltage indicator		LED green
Functional safety related parameters
MTTF_d		210 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Analog output
Output type		1 current output: 4 ... 20 mA 1 voltage output: 0 ... 10 V
Load resistor		current output: &le 400 &Omega voltage output: &ge 1000 &Omega
Short-circuit protection		voltage output: pulsing
Compliance with standards and directives
Standard conformity
	Standards	EN 60947-5-2:2007 IEC 60947-5-2:2007
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		4-pin, M12 x 1 connector
Housing length L		400 mm
Degree of protection		IP65
Material
	Housing	PA 6 / AL
	Target	mild steel, e. g. 1.0037, SR235JR (formerly St37-2)
Note		The data relating to accuracy only apply to a distance to the object to be detected of 1 ... 6 mm.

Частотный преобразователь Frequency Converter with Direction and Synchronization Monitor KFD2-UFT-Ex2.D Pepperl+Fuchs

Каталожный номер: 231200

Описание оборудования
24 V DC

Повторитель Voltage Repeater KFD2-VR4-Ex1.26 Pepperl+Fuchs

Каталожный номер: 196355

General specifications
Signal type		Analog input
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 2
Supply
Connection		Power Rail or terminals 11+, 12-
Rated voltage		19 ... 30 V DC
Ripple		within the supply tolerance
Power dissipation		&le 1.2 W
Power consumption		&le 1.6 W
Input
Connection side		field side
Connection		terminals 4 (common), 1, 3 and 5 (supply -), 2 and 6 (signal -)
Input resistance		10 k&Omega terminals 4 (common), 6-/2-
Output rated operating current		terminals 4 (common), 5-: > 10 mA at -21 V or > 20 mA at -18 V terminals 4 (common), 1-: 5.3 mA ±0.4 mA at -10 V terminals 4 (common), 3-: 3.6 mA ±0.7 mA at -10 V, 20 °C (68 °F)
Transmission range		-20 ... 0 V
Output
Connection side		control side
Connection		terminals 7-, 8+
Load		&ge 9 k&Omega (3-wire sensor), &ge 2 k&Omega (2-wire sensor)
Voltage		-20 ... 0 V
Output resistance		24 &Omega typ., 27 &Omega maximum Since this is much less than the end-to-end resistance of a zener barrier, it may be necessary to specify a monitor intended for use without a barrier. Please follow the advice of the monitor manufacturer.
Transfer characteristics
Cut-off frequency		10 kHz (-0,1 dB) 20 kHz (-1 dB)
Deviation		DC transfer error (with 10 k&Omega load) < 10mV
Time delay relative to input		7.1 ±0.3 µs
Ripple		in 200 kHz bandwidth < 20 mV_rms in 20 kHz bandwidth < 3 mV_rms
Indicators/settings
Display elements		LED
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		screw terminals
Mass		approx. 125 g
Dimensions		20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) , housing type B2
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BAS 02 ATEX 7206
	Marking	II (1)GD, [Ex ia Ga] IIC, [Ex ia Da] IIIC, (-20 °C &le T_amb &le 60 °C) [circuit(s) in zone 0/1/2]
EU-Type Examination Certificate		DMT 01 ATEX E 133
	Marking	I (M1) [Ex ia] I
Certificate		TÜV 99 ATEX 1499 X
	Marking	II 3G Ex nA II T4 [device in zone 2]
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 , EN 50303:2000
International approvals
UL approval
	Control drawing	116-0316 (cULus)
IECEx approval		IECEx BAS 05.0078 IECEx BAS 10.0085X
	Approved for	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex nA II T4 Gc

General specifications
Switching function		Normally open (NO)
Output type		NAMUR with safety function
Rated operating distance		3 mm
Installation		flush in mild steel
Assured operating distance		0 ... 2.4 mm
Actual operating distance		2.7 ... 3.3 mm typ.
Reduction factor r_Al		1
Reduction factor r_Cu		1
Reduction factor r₃₀₄		0
Safety Integrity Level (SIL)		up to SIL3 acc. to IEC 61508 Danger! In safety-related applications the sensor must be operated with a qualified fail safe interface from Pepperl+Fuchs, such as KFD2-SH-EX1. Consider the "exida Functional Safety Assessment" document which is available on www.pepperl-fuchs.com as an integral part of this product's documentation.
Nominal ratings
Nominal voltage		8.2 V
Switching frequency		0 ... 200 Hz
Current consumption
	Measuring plate not detected	&le 1 mA
	Measuring plate detected	&ge 3 mA
Functional safety related parameters
MTTF_d		10660 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		cable silicone , 10 m
Core cross-section		0.75 mm²
Housing material		Crastin (PBTB), black
Sensing face		Crastin (PBTB), black
Housing diameter		18 mm
Degree of protection		IP68
Cable
	Bending radius	> 10 x cable diameter
Note		only for non-ferrous metal
Equipment protection level Gc (nA)
Certificate of Compliance		PF 15CERT3754 X
Special conditions
	Protection against transients	Ensure transient protection is provided and that the maximum value of the transient protection (140% of 85 V) is not exceeded.
Equipment protection level Dc (tc)
Instruction		Manual electrical apparatus for hazardous areas
Device category 3D		for use in hazardous areas with combustible dust
Certificate of Compliance		PF 15CERT3774 X
CE marking		[PD-Z02586A]
ATEX marking		II 3D Ex tc IIIC T80°C Dc The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure "tc" Some of the information in this instruction manual is more specific than the information provided in the datasheet.
General		The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
Installation, commissioning		Laws and/or regulations and standards governing the use or intended usage goal must be observed. The adhesive label provided must be affixed in the immediate vicinity of the sensor! The surface to which the label is applied must be clean, flat and free from grease! The affixed adhesive label must be readable and durable, taking account of the possibility of chemical corrosion!
Maintenance		No changes can be made to apparatus, which are operated in hazardous areas. Repairs to these apparatus are not possible.
Special conditions
	Minimum series resistance R_V	A minimum series resistance RV is to be provided between the power supply voltage and the proximity switch in accordance with the following list. This can also be assured by using a switch amplifier.
	Maximum operating voltage U_Bmax	The maximum permissible operating voltage UBmax must be restricted to the values given in the following list. Tolerances are not permitted.
	Maximum permissible ambient temperature T_Umax	Values can be obtained from the following list, depending on the max. operating voltage Ub max and the minimum series resistance Rv.
	at U_Bmax=9 V, R_V=562 &Omega	58 °C (136.4 °F)
	using an amplifier in accordance with EN 60947-5-6	331 K
	Protection from mechanical danger	The sensor must not be exposed to ANY FORM of mechanical danger.
	Protection from UV light	The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor is used in internal areas.
	Protection of the connection cable	The connection cable must be prevented from being subjected to tension and torsional loading.
	Electrostatic charge	Avoid electrostatic charges that can cause electrostatic discharge when installing or operating the device. Information on electrostatic hazards can be found in the technical specification IEC/TS 60079-32-1. Do not attach the nameplate provided in areas where electrostatic charge can build up.
General information
Use in the hazardous area		see instruction manuals
	Category	1G 2G 3G 1D 3D

Индуктивный датчик Inductive analog sensor NBB5-18GM60-I3-V1 Pepperl+Fuchs

Описание товара

Характеристики

Важная информация

Условия поставки

Способы оплаты

Получение и доставка

Способ доставки

Гарантийные обязательства

Важная информация

Клиенты

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		8 mm
Installation		non-flush
Assured operating distance		0 ... 6.48 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 200 Hz
Hysteresis		typ. %
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	&le 1 mA
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Mechanical specifications
Connection type		cable PVC , 20 m
Core cross-section		0.75 mm²
Housing material		PBT/PPS
Sensing face		PBT
Housing diameter		18 mm
Degree of protection		IP68
Cable
	Bending radius	> 10 x cable diameter
General information
Use in the hazardous area		see instruction manuals
	Category	2G 1D

Индуктивный датчик Inductive analog sensor NBB5-18GM60-I3-V1 Pepperl+Fuchs

Поделиться

Описание товара

Характеристики

Важная информация

Условия поставки

Способы оплаты

Получение и доставка

Способ доставки

Гарантийные обязательства

Важная информация

Клиенты

Рекомендуем

Покупатели, которые приобрели Индуктивный датчик Inductive analog sensor NBB5-18GM60-I3-V1 Pepperl+Fuchs, также купили