Купить Pepperl+Fuchs в интернет-магазине Zipstore.ru

Индуктивный датчик Inductive sensor NBB1-3M22-E0-0,3M-V3 Pepperl+Fuchs

Каталожный номер: 224127

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.29
Reduction factor r₃₀₄		0.76
Reduction factor r_Brass		0.46
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 700 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.1 mA typ. at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Cable connector M8 x 1 , 3-pin with PVC cable 300 mm
Core cross-section		0.055 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PC
Housing diameter		3 mm
Degree of protection		IP67

Интерфейс Multi-Input/Output Device with Aluminum Housing F2D0-MIO-Ex12.PA.* Pepperl+Fuchs

Каталожный номер: T179186

General specifications
Design / Mounting		Outside installation
Electronic component		Binary multi-input/output R8D0-MIO-Ex12.PA* For technical data on installed electronic component see data sheet.
Fieldbus interface
Fieldbus type		PROFIBUS PA
Galvanic isolation
Foundation Fieldbus/Field circuit		safe galvanic isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Standard conformity
Galvanic isolation		EN 60079-11
Electromagnetic compatibility		NE 21:2011
Degree of protection		IEC 60529
Fieldbus standard		IEC 61158-2
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F) hazardous area
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		&le 95 % non-condensing
Shock resistance		15 g , 11 ms
Vibration resistance		10 g , 10 ... 150 Hz
Corrosion resistance		acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Connection type		plug-in terminals , spring terminal and screw terminal
Core cross-section
	Bus	up to 2.5 mm²
	Inputs	up to 2.5 mm²
Cable diameter		see table 2
Cable gland		sensor inputs M16, fieldbus M20
Housing material		EN 1780-1 46000 , ISO AlSi9Cu3(Fe) , anodized
Degree of protection		IP66
Mass		1800 g
Mounting		panel mounting
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 16 ATEX E 075 X
	Marking	II 2 (1) G Ex ib [ia Ga] IIC T4 Gb , II 3 (1) G Ex ic [ia Ga] IIC T4 Gc , II 3 (1) G Ex ec [ia Ga] IIC T4 Gc , I (M1) [Ex ia Ma] I , II (1) D [Ex ia Da] IIIC , II 2 (1) D Ex tb [ia Da] IIIC T130 °C Db
Bus		FISCO see EC-Type Examination Certificate
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 , EN 60079-7:2015 , EN 60079-11:2012 , EN 60079-31:2014
International approvals
IECEx approval		IECEx BVS 16.0051X
	Approved for	Ex ib [ia Ga] IIC T4 Gb , Ex ic [ia Ga] IIC T4 Gc , Ex ec [ia Ga] IIC T4 Gc , [Ex ia Ma] I , [Ex ia Da] IIIC , Ex tb [ia Da] IIIC T130 °C Db
Certificates and approvals
Marine approval		pending

Интерфейс Temperature Multi-Input Device with Aluminum Housing F2D0-TI-Ex8.PA.* Pepperl+Fuchs

Каталожный номер: T165021

General specifications
Design / Mounting		Outside installation
Electronic component		Temperature Multi-Input Device RD0-TI-Ex8.PA* For technical data on installed electronic component see data sheet.
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Standard conformity
Galvanic isolation		EN 60079-11
Electromagnetic compatibility		NE 21:2011
Degree of protection		IEC 60529
Fieldbus standard		IEC 61158-2
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		see table 1
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		&le 95 % non-condensing
Shock resistance		15 g , 11 ms
Vibration resistance		10 g , 10 ... 150 Hz
Corrosion resistance		acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Connection type		plug-in terminals , spring terminal and screw terminal
Core cross-section
	Bus	up to 2.5 mm²
	Inputs	up to 2.5 mm²
Cable diameter		see table 2
Cable gland		sensor inputs M16, fieldbus M20
Housing material		EN 1780-1 46000 , ISO AlSi9Cu3(Fe) , anodized
Degree of protection		IP66
Mass		1800 g
Mounting		panel mounting
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2237
	Marking	II 2 (1) G Ex ia [ia Ga] IIC T4 Gb , II (1) G [Ex ia Ga] IIC , II (1) D [Ex ia Da] IIIC , II 3 G Ex ic IIC T4 Gc
Bus		FISCO see EC-Type Examination Certificate
	Voltage U_i	24 V
Inputs		see EC-Type Examination Certificate
Certificate		PTB 03 ATEX 2238 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Bus	see Statement of Conformity
	Input	see EC-Type Examination Certificate
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
FM approval		CoC 3025732
CSA approval		CoC 3025732C
IECEx approval		IECEx PTB 05.0001 , IECEx PTB 05.0002X
	Approved for	Ex ia [ia Ga] IIC T4 Gb , [Ex ia Ga] IIC , [Ex ia Da] IIIC , Ex ic IIC T4 Gc , Ex nA IIC T4 Gc
Certificates and approvals
Marine approval		DNV A-14038

Интерфейс Multi-Input/Output Device for Cabinet Installation R8D0-MIO-Ex12.PA* Pepperl+Fuchs

Каталожный номер: T179189

General specifications
Design / Mounting		Cabinet installation
Fieldbus interface
Fieldbus type		PROFIBUS PA
FDE (Fault Disconnect Equipment)		6.7 mA
Polarity		not polarity sensitive
Rated voltage		9 ... 32 V
Rated current		max. 23 mA
Indicators/operating means
LED PWR		green: on, bus voltage existent
LED COM ERR		red, continuous lightning: hardware error red, flashing: no bus activities or bus fault off: no error
LED CHANNEL ERROR		red, flashing: lead breakage/short circuit off: no error
DIP switch		Address setting , write protection , simulation
Analog input
Number of inputs		1
Input type		Frequency input / Counter Input , channel 1
Switching frequency		min. 0.1 Hz max. 5 kHz
Pulse duration		min. 80 µs
Supply voltage		5 V
Supply current		5 mA
Line fault detection		lead breakage , short circuit (not in counter mode)
Digital input
Number of inputs		12
Input type		Sensor input , channels 1, 4, 7, 10 multiplexed , cycle adjustable
	Supply voltage	6.6 V
	Supply current	5 mA
	Line fault detection	lead breakage , short circuit
Input type		Sensor input , channels 2, 3, 5, 6, 8, 9, 11, 12 multiplexed , cycle fixed
	Supply voltage	5 V
	Supply current	5 mA
	Time delay before availability	2 ms
	Line fault detection	lead breakage , short circuit
Digital output
Number of outputs		4
Output type		Low power valve , channels 1, 4, 7, 10
Supply voltage		6.6 V
Supply current		1.5 mA
Line fault detection		lead breakage , short circuit
Galvanic isolation
Foundation Fieldbus/Field circuit		safe galvanic isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Standard conformity
Galvanic isolation		EN 60079-11
Electromagnetic compatibility		NE 21:2011
Degree of protection		IEC/EN 60529
Fieldbus standard		IEC 61158-2
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-50 ... 75 °C (-58 ... 167 °F) hazardous area -50 ... 85 °C (-58 ... 185 °F) safe area
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		&le 95 % non-condensing
Shock resistance		15 g , 11 ms
Vibration resistance		5 g , 10 ... 150 Hz
Pollution degree		2
Corrosion resistance		acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Connection type		plug-in terminals , spring terminal and screw terminal
Core cross-section
	Bus	up to 2.5 mm²
	Inputs	up to 2.5 mm²
Housing material		Polycarbonate
Degree of protection		IP20
Mass		approx. 290 g
Mounting		mounting on DIN rail in cabinet
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 16 ATEX E 075 X
	Marking	II 2 (1) G Ex ib [ia Ga] IIC T4 Gb , II 3 (1) G Ex ic [ia Ga] IIC T4 Gc , II 3 (1) G Ex ec [ia Ga] IIC T4 Gc , I (M1) [Ex ia Ma] I , II (1) D [Ex ia Da] IIIC
PROFIBUS PA
	Maximum safe voltage U_m	253 V
	Voltage U_i	24 V
	Current I_i	380 mA
	Power P_i	5.32 W
Field-side
	Voltage U_o	9 V
	Current I_o	43 mA
	Power P_o	96 mW
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-7:2015
International approvals
IECEx approval		IECEx BVS 16.0051X
	Approved for	Ex ib [ia Ga] IIC T4 Gb , Ex ic [ia Ga] IIC T4 Gc , Ex ec [ia Ga] IIC T4 Gc , [Ex ia Da] IIIC , [Ex ia Ma] I
Certificates and approvals
Marine approval		pending

Индуктивный датчик Inductive sensor NBB1-3M22-E2-0,3M-V3 Pepperl+Fuchs

Каталожный номер: 224128

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.29
Reduction factor r₃₀₄		0.76
Reduction factor r_Brass		0.46
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 700 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.1 mA typ. at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1340 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Cable connector M8 x 1 , 3-pin with PVC cable 300 mm
Core cross-section		0.055 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PC
Housing diameter		3 mm
Degree of protection		IP67

Интерфейс Temperature Multi-Input Device for Cabinet Installation RD0-TI-Ex8.PA.* Pepperl+Fuchs

Каталожный номер: T163902

General specifications
Design / Mounting		Cabinet installation
Fieldbus interface
Fieldbus type		PROFIBUS PA
Firmware update		via separate plug connection
FDE (Fault Disconnect Equipment)		6.7 mA
Polarity		not polarity sensitive
Rated voltage		9 ... 32 V
Rated current		max. 23 mA
PROFIBUS PA
	Profile	3.02
Indicators/operating means
LED PWR		green: on, bus voltage existent
LED COM ERR		red, continuous lightning: hardware error red, flashing: no bus activities or bus fault off: no error
LED CHANNEL ERROR		red: 2 Hz flashing: lead breakage, overrange off: no error
Input
Number		8
Sensor types		see table 1
Grounding		grounding of thermoelements possible
Error detection		lead breakage, wiring error, hardware device error
Common mode voltage		Input to Input 600 V_peak
Transfer characteristics
Deviation
	Influence of ambient temperature	see table 3
	Linearization	T/C input 0.1°C RTD input 0.03°C
Internal measurement cycle		for all sensor types max. 1 s
Galvanic isolation
Fieldbus/inputs		safe galvanic isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Standard conformity
Galvanic isolation		EN 60079-11
Electromagnetic compatibility		NE 21:2011
Degree of protection		IEC 60529
Fieldbus standard		IEC 61158-2
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F) hazardous area -40 ... 85 °C (-40 ... 185 °F) safe area
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		&le 95 % non-condensing
Shock resistance		15 g , 11 ms
Vibration resistance		5 g , 10 ... 150 Hz
Corrosion resistance		acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Connection type		plug-in terminals , spring terminal and screw terminal
Core cross-section
	Bus	up to 2.5 mm²
	Inputs	up to 2.5 mm²
Housing material		Polycarbonate
Degree of protection		IP20
Mass		360 g
Mounting		mounting on DIN rail in cabinet
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2237
	Marking	II 2 (1) G Ex ia [ia Ga] IIC T4 Gb , II (1) G [Ex ia Ga] IIC , II (1) D [Ex ia Da] IIIC , II 3 G Ex ic IIC T4 Gc
Bus		FISCO see EC-Type Examination Certificate
	Voltage U_i	24 V
Inputs		see EC-Type Examination Certificate
Certificate		PTB 03 ATEX 2238 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Bus	see Statement of Conformity
	Input	see EC-Type Examination Certificate
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
FM approval		CoC 3025732
CSA approval		CoC 3025732C
IECEx approval		IECEx PTB 05.0001 , IECEx PTB 05.0002X
	Approved for	Ex ia [ia Ga] IIC T4 Gb , [Ex ia Ga] IIC , [Ex ia Da] IIIC , Ex ic IIC T4 Gc , Ex nA IIC T4 Gc
Certificates and approvals
Marine approval		DNV A-14038

Изолятор Ethernet Intrinsically safe Ethernet Isolator EI-0D2-10Y-10B Pepperl+Fuchs

Каталожный номер: 194658

Supply
Rated voltage		19.2 ... 35 V DC
Rated current		150 ... 100 mA
Power dissipation		3 W
Ethernet Interface
Intrinsically safe port		10 BASE-T/100 BASE-TX
Non-intrinsically safe port		10 BASE-T/100 BASE-TX
Connection type		2 x RJ-45 , IEC 60603-7
Connector pinout		socket TIA/EIA-568-B
Transfer rate		10/100 Mbit/s , Auto-Negotiation
Operating mode		Half/Full Duplex
Cable type		CAT5e S/FTP AWG 24, Installation cable, L/R ratio max. 10 µH/&Omega of all strand combinations
I.S. cable length		typ. 100 m/20 °C
Total cable length		typ. 200 m/20 °C
Number of isolators		max. 2 in series connection
Indicators/operating means
LED PWR		green: Power on
LED ACT		yellow: communication active
LED 10/100		yellow ON: Transfer rate 100 MBit/s , OFF: 10 MBit/s
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Standard conformity
Galvanic isolation		EN 50020
Degree of protection		IEC 60529
Climatic conditions		DIN IEC 721
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ethernet		IEEE 802.3 , IEEE 802.3u
Ambient conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		&le 95 % non-condensing
Shock resistance		15 g 11 ms
Vibration resistance		1 g 10 ... 150 Hz
Pollution degree		max. 2, according to IEC 60664
Mechanical specifications
Connection type		Terminals
Core cross-section		up to 2.5 mm²
Housing material		Polyamide PA 66
Degree of protection		IP20 according to EN 60529
Mass		195 g
Mounting		DIN rail mounting
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 07 ATEX 2025 X
	Marking	II (1) G [Ex ia Ga] IIB , II (1) D [Ex ia Da] IIIC , II 3(1)G Ex nA [ia Ga] IIB T4 Gc II 3 (1D) G Ex nA [ia IIIC Da] IIB T4 Gc I (M1) [Ex ia Ma] I
Supply
	Maximum safe voltage	253 V AC
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
CSA approval		CSA 15.70016295
	Control drawing	116-B032
	Approved for	Class I, Zone 2, AEx/Ex nA [ia Ga] IIB T4 Gc Class I, Zone 2, AEx/Ex nA [ia Da IIIC] IIB T4 Gc
IECEx approval		IECEx PTB 09.0053X
	Approved for	[Ex ia Ga] IIB [Ex ia Da] IIIC Ex nA [ia Ga] IIB T4 Gc Ex nA [ia IIIC Da] IIB T4 Gc [Ex ia Ma] I
Certificates and approvals
Patents		This product may be covered by the following patent: US7,687,791

Индуктивный датчик Inductive sensor NBB1-4GM22-E0 Pepperl+Fuchs

Каталожный номер: 206384

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.29
Reduction factor r₃₀₄		0.76
Reduction factor r_Brass		0.46
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 700 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.1 mA typ. at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.055 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PC
Housing diameter		4 mm
Degree of protection		IP67

Изолятор Ethernet Intrinsically safe Ethernet Isolator EI-0D2-10Y-10B-Y1 Pepperl+Fuchs

Каталожный номер: 268091

Supply
Rated voltage		19.2 ... 35 V DC
Rated current		150 ... 100 mA
Power dissipation		3 W
Ethernet Interface
Intrinsically safe port		10 BASE-T/100 BASE-TX
Non-intrinsically safe port		10 BASE-T/100 BASE-TX
Connection type		2 x RJ-45 , IEC 60603-7
Connector pinout		socket TIA/EIA-568-B
Transfer rate		10/100 Mbit/s , Auto-Negotiation
Operating mode		Half/Full Duplex
Cable type		CAT5e S/FTP AWG 24, Installation cable, L/R ratio max. 10 µH/&Omega of all strand combinations
I.S. cable length		typ. 100 m/20 °C
Total cable length		typ. 200 m/20 °C
Number of isolators		max. 2 in series connection
Indicators/operating means
LED PWR		green: Power on
LED ACT		yellow: communication active
LED 10/100		yellow ON: Transfer rate 100 MBit/s , OFF: 10 MBit/s
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Standard conformity
Galvanic isolation		EN 50020
Degree of protection		IEC 60529
Climatic conditions		DIN IEC 721
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ethernet		IEEE 802.3 , IEEE 802.3u
Ambient conditions
Ambient temperature		-20 ... 55 °C (-4 ... 131 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		&le 95 % non-condensing
Shock resistance		15 g 11 ms
Vibration resistance		1 g 10 ... 150 Hz
Pollution degree		max. 2, according to IEC 60664
Mechanical specifications
Connection type		Terminals
Core cross-section		up to 2.5 mm²
Housing material		Polyamide PA 66
Degree of protection		IP20 according to EN 60529
Mass		195 g
Mounting		DIN rail mounting
Data for application in connection with hazardous areas
EC-Type Examination Certificate		PTB 07 ATEX 2025 X
	Group, category, type of protection, temperature class	II (1) GD [Ex ia] IIB , II 3 (1GD) G Ex nA [ia IIB] II T4 , I (M1) [Ex ia] I
Supply
	Maximum safe voltage	253 V AC
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-15:2010
Certificates and approvals
Patents		This product may be covered by the following patent: US7,687,791

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator FB3305B2 Pepperl+Fuchs

Каталожный номер: 238487

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART):Supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14-3-wire transmitter:Supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16-Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-4-wire transmitter (powered externally):Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		Ex e spring terminal with protective cover
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 093 X
	Marking	II 2 G Ex db eb IIC T4
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007
International approvals
ATEX approval		BVS 11 ATEX E 093X
INMETRO		Brazil: TÜV 14.1599X
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator FB3205B2 Pepperl+Fuchs

Каталожный номер: 236589

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART):Supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14-3-wire transmitter:Supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16-Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-4-wire transmitter (powered externally):Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 101 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	90 mA
	Power	588 mW (linear characteristic)
Input
	Voltage	0.7 V
	Current	2.78 mA
	Power	2 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2012 EN 60079-26:2007
International approvals
ATEX approval		BVS 12 ATEX E 101 X
INMETRO		Brazil: TÜV 14.1597X
Marine approval
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB1-4GM22-E0-0,3M-V3 Pepperl+Fuchs

Каталожный номер: 224131

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.29
Reduction factor r₃₀₄		0.76
Reduction factor r_Brass		0.46
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 700 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.1 mA typ. at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Cable connector M8 x 1 , 3-pin with PVC cable 300 mm
Core cross-section		0.055 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PC
Housing diameter		4 mm
Degree of protection		IP67

Компонент аналогового входа Transmitter Power Supply, Input Isolator FB3201B2 Pepperl+Fuchs

Каталожный номер: 270476

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter: supply circuit: 2/3+, 4/5- 3-wire transmitter: supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6)
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		no
HART secondary variable		no
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 13 ATEX E 050 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	23.8 V
	Current	90 mA
	Power	533 mW (linear characteristic)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2012 EN 60079-26:2007
International approvals
INMETRO		Brazil: TÜV 14.1596X
Marine approval
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator FB3202B1 Pepperl+Fuchs

Каталожный номер: 243085

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 015 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007
International approvals
ATEX approval		BVS 12 ATEX E 015 X
INMETRO		Brazil: TÜV 14.1595X
Marine approval
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator FB3202B2 Pepperl+Fuchs

Каталожный номер: 270479

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 13 ATEX E 050 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	92 mA
	Power	619 mW (linear characteristic)
Connection 1-6
	Voltage	8.9 V
	Current	4 mA
	Power	24 mW (trapezoid characteristic curve)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2012 EN 60079-26:2007
International approvals
ATEX approval		BVS 13 ATEX E 050 X
INMETRO		Brazil: TÜV 14.1596X
Marine approval
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB1-4GM22-E2-0,3M-V3 Pepperl+Fuchs

Каталожный номер: 224132

General specifications
Switching function		Normally open (NO)
Output type		PNP
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.29
Reduction factor r₃₀₄		0.76
Reduction factor r_Brass		0.46
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 700 Hz
Hysteresis		typ. 5%
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 100 mA
Off-state current		0 ... 0.1 mA typ. at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1340 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		Cable connector M8 x 1 , 3-pin with PVC cable 300 mm
Core cross-section		0.055 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PC
Housing diameter		4 mm
Degree of protection		IP67

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator FB3203B2 Pepperl+Fuchs

Каталожный номер: 270481

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 13 ATEX E 050 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	24.9 V
	Current	77 mA
	Power	478 mW (linear characteristic)
Connection 1-6
	Voltage	8.9 V
	Current	4 mA
	Power	24 mW (trapezoid characteristic curve)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2012 EN 60079-26:2007
International approvals
INMETRO		Brazil: TÜV 14.1596X
Marine approval
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового входа Transmitter Power Supply, Input Isolator FB3204B2 Pepperl+Fuchs

Каталожный номер: 239397

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter: supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14- 3-wire transmitter: supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16- measuring circuit: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16- 4-wire transmitter (separately powered): measuring circuit: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Conversion time		max. 100 ms
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		no
HART secondary variable		no
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 12 ATEX E 101 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	90 mA
	Power	588 mW (linear characteristic)
Input
	Voltage	0.7 V
	Current	2.78 mA
	Power	2 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2012 EN 60079-26:2007
International approvals
ATEX approval		BVS 12 ATEX E 101 X
INMETRO		Brazil: TÜV 14.1597X
Marine approval
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB1-5GM30-E0-0,5M-Y248061 Pepperl+Fuchs

Каталожный номер: 248061

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.35
Reduction factor r₃₀₄		0.78
Reduction factor r_Brass		0.52
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 3000 Hz
Hysteresis		1 ... 15 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.1 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 10 mA
Switching state indicator		LED, red
Approvals and certificates
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 0.5 m
Core cross-section		0.14 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		POM
Housing diameter		5 mm
Degree of protection		IP67

Компонент аналогового входа HART Transmitter Power Supply, Input Isolator FB3302B2 Pepperl+Fuchs

Каталожный номер: 270483

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega (terminals 5, 6) 236 &Omega (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		Ex e spring terminal with protective cover
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 093 X
	Marking	II 2 G Ex db eb IIC T4
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007
International approvals
ATEX approval		BVS 11 ATEX E 093X
INMETRO		Brazil: TÜV 14.1599X
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input FB1208B Pepperl+Fuchs

Каталожный номер: 542070

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power consumption		0.7 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Input
Digital signals (active)
	Switching point: ON
Digital input
Number of channels		8
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
Connection		channel I: 1+, 2- channel II: 3+, 4- channel III: 5+, 6- channel IV: 7+, 8- channel V: 9+, 10- channel VI: 11+, 12- channel VII: 13+, 14- channel VIII: 15+, 16-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb II (1) D [Ex ia Da] IIIC
Input
	Voltage	14.9 V
	Current	15.7 mA
	Power	58.2 mW (linear characteristic)
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075 PTB 97 ATEX 1074 U
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input FB1201B Pepperl+Fuchs

Каталожный номер: 542066

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 2/3- channel II: 4+, 5/6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault, channel 1 LED yellow: status channel 1
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb II (1) D [Ex ia Da] IIIC
Input
	Voltage	12.6 V
	Current	12.8 mA
	Power	40.1 mW (linear characteristic)
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075 PTB 97 ATEX 1074 U
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB1-8GS50-Z0-T Pepperl+Fuchs

Каталожный номер: 236475

General specifications
Switching function		Normally open (NO)
Output type		Two-wire
Rated operating distance		1 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 0.81 mm
Actuating element		mild steel, e. g. 1.0037, SR235JR (formerly St37-2) 8 mm x 8 mm x 1 mm
Reduction factor r_Al		0.38
Reduction factor r_Cu		0.2
Reduction factor r₃₀₄		0.8
Reduction factor r_Brass		0.45
Nominal ratings
Installation conditions
	B	4 mm
	C	3 mm
	F	12 mm
Operating voltage		15 ... 34 V
Switching frequency		0 ... 1500 Hz
Hysteresis		0.01 ... 0.28 mm
Reverse polarity protection		no
Short-circuit protection		no
Overload resistance		no
Wire breakage protection		yes
Inductive overvoltage protection		yes
Surge suppression		yes
Ripple		10 %
Voltage drop		&le 8 V
Repeat accuracy		0.1 mm
Operating current		0 ... 25 mA
No-load supply current		&le 1.5 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		2390 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		0.25 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Housing diameter		8 mm
Degree of protection		IP67
Mass		70 g

Индуктивный датчик Inductive sensor NBB10-30GK50-E0 Pepperl+Fuchs

Каталожный номер: 88550

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		10 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 8.1 mm
Reduction factor r_Al		0.3
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.8
Nominal ratings
Operating voltage		10 ... 30 V
Switching frequency		0 ... 200 Hz
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop		&le 3 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 0.1 µA at 25 °C
No-load supply current		&le 20 mA
Switching state indicator		all direction LED, yellow
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated &le36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.34 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Note		use only delivered nuts

Компонент цифрового входа Digital Input FB1202B Pepperl+Fuchs

Каталожный номер: 542067

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		3
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 4- channel II: 2+, 5- channel III: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault, channel 1 LED yellow: status channel 1
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 330 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2(1) G Ex d [ia Ga] IIC Gb II (1) D [Ex ia Da] IIIC
Input
	Voltage	10.5 V
	Current	35 mA
	Power	92 mW (linear characteristic)
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		PTB 97 ATEX 1075 PTB 97 ATEX 1074 U
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input FB1301B2 Pepperl+Fuchs

Каталожный номер: 238482

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 2/3- channel II: 4+, 5/6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault, per channel LED yellow: signal (status), per channel
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		Ex e spring terminal with protective cover
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 093 X
	Marking	II 2 G Ex db eb IIC T4
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007
International approvals
ATEX approval		BVS 11 ATEX E 093X
INMETRO		Brazil: TÜV 14.1599X
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input FB1302B2 Pepperl+Fuchs

Каталожный номер: 238483

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		3
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 4- channel II: 2+, 5- channel III: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault, per channel LED yellow: signal (status), per channel
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		Ex e spring terminal with protective cover
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 093 X
	Marking	II 2 G Ex db eb IIC T4
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007
International approvals
ATEX approval		BVS 11 ATEX E 093X
INMETRO		Brazil: TÜV 14.1599X
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB10-30GK50-E0-M Pepperl+Fuchs

Каталожный номер: 248874

General specifications
Switching function		Normally open (NO)
Output type		NPN
Rated operating distance		10 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 8.1 mm
Reduction factor r_Al		0.35
Reduction factor r_Cu		0.25
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.4
Output type		3-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 800 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Inductive overvoltage protection		yes
Surge suppression		yes
Voltage drop		&le 2 V
Rated insulation voltage		60 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 6 µA at 25 °C
No-load supply current		&le 7 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		830.5 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CSA approval		cCSAus Listed, General Purpose, Class 2 Power Source
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		3 x 0.75 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Mass		156 g

Компонент цифрового входа Digital Input FB1308B2 Pepperl+Fuchs

Каталожный номер: 238485

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power consumption		0.7 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		8
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 2- channel II: 3+, 4- channel III: 5+, 6- channel IV: 7+, 8- channel V: 9+, 10- channel VI: 11+, 12- channel VII: 13+, 14- channel VIII: 15+, 16-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Digital signals (active)		configurable 24 V 5 V
	Switching point: ON	> 8 V > 2.7 V
	Switching point: OFF	< 3 V < 2.3 V
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool , active signals (24 V, 5 V) without line fault detection
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault , red flashing: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		Ex e spring terminal with protective cover
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 093 X
	Marking	II 2 G Ex db eb IIC T4
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007
International approvals
ATEX approval		BVS 11 ATEX E 093X
INMETRO		Brazil: TÜV 14.1599X
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Индуктивный датчик Inductive sensor NBB10-30GK50-E1-M Pepperl+Fuchs

Каталожный номер: 248875

General specifications
Switching function		Normally closed (NC)
Output type		NPN
Rated operating distance		10 mm
Installation		flush
Output polarity		DC
Assured operating distance		0 ... 8.1 mm
Reduction factor r_Al		0.35
Reduction factor r_Cu		0.25
Reduction factor r₃₀₄		0.7
Reduction factor r_Brass		0.4
Output type		3-wire
Nominal ratings
Operating voltage		5 ... 60 V
Switching frequency		0 ... 800 Hz
Hysteresis		typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Inductive overvoltage protection		yes
Surge suppression		yes
Voltage drop		&le 2 V
Rated insulation voltage		60 V
Operating current		0 ... 200 mA
Off-state current		0 ... 0.5 mA typ. 6 µA at 25 °C
No-load supply current		&le 7 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		830.5 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Approvals and certificates
UL approval		cULus Listed, General Purpose, Class 2 Power Source
CSA approval		cCSAus Listed, General Purpose, Class 2 Power Source
CCC approval		Certified by China Compulsory Certification (CCC)
E1 Type approval		10R-04
Ambient conditions
Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		cable PUR , 2 m
Core cross-section		3 x 0.75 mm²
Housing material		PBT
Sensing face		PBT
Housing diameter		30 mm
Degree of protection		IP68 / IP69K
Mass		156 g

Запасные части Pepperl+Fuchs

Каталог запчастей Pepperl+Fuchs

Купить запчасти для Pepperl+Fuchs оптом и в розницу

Техподдержка