CF-2141; Single-channel external CIB bus master, communication with CP-Ethernet

C-IR-0203M is a module on the CIB bus with a total of 5 inputs / outputs in combination: 2 AI / DI inputs 2 relay outputs with changeover contact (each contact shown separately on the terminal board) 1 AO output with a range of 0 to 10V, or with a PWM output with adjustable amplitude and frequency. Use: Closed loop control with proportional control (PWM output) or two-point control (relay) Control of valves, motors, lighting switching, heating cartridges and other...

C-OR-0202M is a module on the CIB bus that it contains 2 relay outputs with changeover contact 16A NO/NC, each separately connected to the terminal board 2 analog / binary inputs for connecting temperature sensors or potential-free contacts. It is mounted in any position in the installation box under the lid or under the device in the installation box. It is powered from the CIB bus

The module contains 2 universal analog inputs for general use, connects to the CIB Common Installation Bus® and has a high coverage for use in outdoor conditions. It allows to measure voltage, current, resistance, resistance temperature sensors and thermocouples. The selection of the type and range of measurement is done by jumpers. The firmware of the module linearizes the characteristics of the resistance sensor, optimizes the accuracy of the measurement and converts it to the...

C-HC-0201F-E is a module connected to the CIB Common Instalation Bus ® designed for proportional control of radiator central heating valves with M30x1.5 fittings. It has integrated 2 universal inputs 2x AI / DI.

C-BM-0202M is a module on the CIB bus, which is designed for monitoring and balancing LiFePO4 cells, especially for stationary energy storage (storage of surplus PV production, backup power supply systems, etc.) composed of individual cells. input for measuring the battery current using a Hall probe. provides a supply voltage of 24 VDC and 5 VDC for powering the Hall probe. terminal block for connection of B-BM-0201X modules monitoring and balancing individual cells. two...

The C-RF-0001M-A peripheral module is the communication interface between the CFox bus and the RFox2 wireless network. It is referred to as the CFox MiniMaster. It allows you to connect up to 10 Rfox2 wireless elements to the system.

The C-IR-0303M is a module on the CIB bus that it contains - 3x AI / DI inputs - 3x relay outputs with switching contact (2 with common input and 1 separately connected to the terminal board). Use: - Valve control, addition of heating circuit control for common installations in the field of HVAC, - Switching of lighting, general loads and appliances - Measurement of up to three quantities by passive / resistance sensors

C-LC-0202M is a module on the CIB bus. It is designed for mounting in an installation box. It contains: - 2 relay outputs 16A (inrush 80) with a switching contact for switching power loads. especially light sources with a high short-term inrush current. - 2 inputs are intended for connection of buttons with potential-free contacts and with evaluation of short and long presses. The inputs are also used for direct control of outputs if the module does not communicate with the CIB master.

Solar radiation measurement module with IP65 protection for outdoor installation. It is used to evaluate the incident energy in the range of 0-1500W / m2. For the measurement, it uses a monocrystalline silicon cell with an integrated temperature sensor for temperature compensation of the measured value. To accurately calculate the intensity in W / m2, enter the individual calibration constant listed on the inside of the lid.

C-AQ-0006R-xxx are room sensors for indoor air quality measurement. They detect - carbon dioxide CO2, - relative humidity RH, - volatile organic compounds iVOC - air temperature T. Built-in autocalibration functions of the sensors guarantee long-term measurement stability. It is connected via the CIB - Common Installation Bus®.

B-BM-0201X is a module for voltage and temperature sensing and for passive balancing of individual LiFePO4 cells connected in series. A series of one input, n continuous and one end module is connected to the C-BM-0202M module, which then communicates with the basic module via the CIB Common Installation Bus®. The balancing of each cell is performed by the module by controlling the load resistance, according to the command from the basic module. Connection: the module is adapted for...

The C-BS-0001M module is a single-channel CIB bus separator for increasing the current consumption (and thus also the number of modules) on the CIB bus for basic modules (CP-xxxx) with possible current consumption from the CIB up to 100mA. That is, for all CP-xxxx except CP-1000, CP-1001 and CP-2000. It allows the connection of 32 modules up to a maximum current of 1A.

C-IB-1800M is a module on the CIB bus, which contains a total of 18 inputs 14 binary inputs - mainly for sensing potential-free contacts These inputs can be switched to the so-called balanced input mode used for security sensors. In this mode, the inputs can also detect sensor disconnection as tamper The module also has a power supply for security sensors requiring 12V DC 4 combined AI / DI inputs not only for binary and balanced inputs, but also for measuring passive...

C-JC-0201B is a module on the CIB bus that contains - 2 relay outputs interlocked, each separately connected to the terminal board - 2 binary inputs for connection of potential-free contacts, which evaluate short and long presses. When the CIB master is not connected or not communicating, the outputs can be controlled manually if the control contacts are connected directly to the module inputs. The module is mechanically designed in the "box" type for mounting in the installation box.

C-AM-0600I - module on the CIB Common Installation Bus®, contains 5 universal inputs and 1 special interface for connecting a turbine-free TacoSetter Tronic flowmeter. Universal inputs can be configured for measurement resistance temperature sensors, Tension, current can be configured as an interface for reading pulses from energy meters, eg electricity meters, gas meters, etc. The TacoSetter Tronic flowmeter interface contains 2 outputs. The first output is the analog...

C-IF-6400R is a matrix of 8 x 8 temperature sensors (64 pixels) on the CIB bus - Common Instalation Bus®. Sensor Grid-EYE is based on MEMS technology. Each pixel, independently of the others, transmits the temperature value directly in engineering units. The range of measured temperatures is from 0 to 80 ° C. Thanks to the silicon lens, it is possible to actively monitor the angle of 60 °. Fast measurement and transfer (1x or 10x per second) of all values to the basic Foxtrot module allows...

The CF-1141 module is a two-channel CIB master with a separator perimeter. Each channel allows the connection of 32 modules to maximum current 1A. Communication with the basic module takes place via the TCL2 interface.

C-IS-0504M is a module on the CIB bus with a total of 9 inputs / outputs in combination 3x combined AI / DI input for sensing contacts and measuring resistance thermometers, 2x analog input specialized for measuring AC resistances (excluding long-term electrolysis in a humid environment - icing, precipitation, level probes) 1x semiconductor output with pulse width modulation (PWM from 100 Hz to 2 kHz and load capacity max. 4W) 2x relay output 5 A, 1x relay output 16A,...

C-DM-0001B-SL is a module connectable to the CIB bus of the Foxtrot system. It contains one DO output for data addressable RGB LED chips type WS2812B, one IN / OUT terminal for synchronization of several modules in a row and a voltage source of 5 V / 1 A for powering a series of up to 16 LEDs. It is equipped with a slot for a microSD card, on which data files for static and dynamic effects are uploaded. which the module "reads" and cyclically sends to a series of connected LED chips.

C-RI-0401I is a combined - temperature - lighting sensor on the CIB bus. The module is in a plastic design with a cable gland and an increased degree of protection, designed for installation in an outdoor environment on a vertical support surface.

BDM-024-V / 1-FR1-CIB Lightning current arrester with two-stage overvoltage protection designed for the CIB bus installation at the entrance to the building near the protected equipment, at the interface of zones LPZ 0 – LPZ 1 and higher can also be used to protect the interfaces of control systems MaR, EZS, EPS, etc. against longitudinal overvoltage (line - protective earth) rough protection and against transverse overvoltage (core - core, GND) rough and fine overvoltage protection...

Module with a total of 8 relay outputs. It is connected to the basic module via a two-wire CIB Common installation BUS. Power supply either from the CIB bus (higher consumption limits the maximum number of modules on one CIB branch) or with amplification directly from a 24 V DC source. Each output has a make (16 A permanent) and break contact (10 A permanent). Each output has a separate LED indication on the front panel. The module can be switched to manual (service) mode...

C-VT-0102B; CIB, 2x Fan driver for inVENTer (±15V DC); 1x AI for termperature sensor

Relative humidity and temperature measurement module. It connects a relative humidity and temperature sensor to the CIB bus (the design of the sensor is determined by the part number). It also allows you to connect two universal inputs that can be used separately as binary or analog. The module is designed for measuring relative humidity and air temperature without aggressive additives indoors, exteriors and in ventilation ducts. It is built into an installation plastic...

DTNVEM 1/CIB surge suppressor for 1xCIB, for DIN rail

C-OR-0011M-800; CIB, 11x RO, switching contact, 230V / 16A (inrush current 800A) Module on the CIB bus, which contains 11 relay outputs with a switching contact, each separately connected to the terminal board.

The C-IT-0200S module is intended for connection of two passive temperature sensors or binary signals from contacts and their conversion to the CIB wiring bus. The resistance from the optional Pt1000, Ni1000, NTC 12k, KTY81-121 sensors against the common GND conductor is linearized in the module and converted directly to a numerical temperature value and then transferred to the basic module via the CIB bus. It is possible to choose the measurement of other resistances in the range of 0 to...

The C-IT-0100H-P module is a temperature sensor -50 ° C to + 250 ° C with IP65 protection, which can be connected directly to the CIB wiring bus. The main Pt1000 temperature sensor is in the stem. The information sensor measures the temperature inside the head. The resistance is measured and converted directly in the module to a numerical temperature value. The values are communicated to the basic module via the CIB Common Installation Bus®. The module thus eliminates...

DTNVE 1 / CIB Surge protection for CIB bus, in the installation box DTNVEM 1 / CIB overvoltage protection is a basic element for protecting your own CIB bus. It only protects against surges that can enter the CIB installation itself. It does not replace the protection of the entire control system. DTNVEM 1 / CIB is a surge protection device (SPD) according to ČSN EN 61643-21 (categories A2, B2, C2, C3, D1) designed to protect the CIB bus against lightning currents and overvoltages. The...