C-JC-0006M; CIB, 6x blind actuator, (6x2 RO - dependent switching, local function), 230VAC / 5A

The C-IR-0202S module is a dimensionally minimalist module on the CIB bus for relay contact control or for continuous control via voltage analog output. At the same time, it is intended for connection of two passive temperature sensors or binary signals from contacts and their conversion into data for the CIB wiring bus. - The resistance from the optional Pt1000, Ni1000, NTC 12k, KTY81-121 sensors against the common GND conductor is linearized in the module and converted directly to a...

C-RM-1109M; CIB, 3x AI, 8X DI, 1x AO, 8x RO, ext. power supply

The C-IT-0202S module is a dimensionally minimized module on the CIB bus for control by two independent analog outputs. At the same time, it is intended for connection of two passive temperature sensors or binary signals from contacts and their conversion into data for the CIB wiring bus. - The resistance from the optional Pt1000, Ni1000, NTC 12k, KTY81-121 sensors against the common GND conductor is linearized in the module and converted directly to a numerical temperature value and then...

C-HM-0308M; CIB, 3x AI/DI, 2x AO, 6x RO/5A

C-IR-0203S is a module designed for connection to the CIB bus. Contains - two combined analog or binary inputs - two analog outputs with a range of 0-10 V - one relay output with changeover contact. Inputs and analog outputs are connected to the terminal block with pen terminals, the relay output to the terminal block with screw cage terminals. - The inputs allow direct connection of resistance sensors PT1000, Ni1000, sensor with thermistor NTC12k or KTY81-121 against a common GND...

The C-HM-1113M modules are designed for connection to the CIB bus. The module contains - 8 binary inputs for contacts - 3 analog inputs with common terminal - 2 analog outputs with common terminal - 11 relay outputs grouped The outputs can be switched manually after switching to manual mode. The analog inputs are configurable according to the type of resistance sensor used, supplied from a common terminal. Analog outputs are with 8 bit resolution, voltage 0 ÷ 10V. The module is...

The C-IT-0504S module (order no .: TXN 133 26) is intended for the connection of analog or binary signals and 0 - 10 V analog outputs directly to the CIB wiring bus. Inputs, outputs and buses are connected to the module via pen terminals. Universal inputs can be set to binary or analog program in two groups. The first group contains 4 inputs, the second 1 input. The settings are then common to the whole group. For example, one temperature sensor and four input-contacts or one input-contact...

Module with a total of 32 inputs and outputs of digital, analog and relay in combination suitable to cover the needs of a typical hotel room or similar spaces.     It is connected to the basic module via the two-wire CIB Common installation BUS for communication.     The power supply is from the 230 V AC network to cover a higher consumption of a large number of inputs and especially relay outputs.     The module has 3 relays with a high permanent load capacity of 16A and resistance to...

C-DL-0012S; CIB-DALI converter, for 12 DALI Ballasts

The C-DM-0002L-10V module is designed for independent two-channel control of electronic LED ballasts or fluorescent lamps, controlled by 0-10 V DC or 1-10 V DC. To completely disconnect the ballasts from the main power supply, the module contains 2 relay outputs, one with an NC contact and the other with changeover contacts. Of course, analog inputs and relay outputs can also be used universally for other purposes. The module is designed for a DIN rail switchboard, but it can also be...

The C-IT-0908S module is intended for the CIB Common Installaton Bus® for the connection of sensing analog or binary signals (sensing potential-free contacts) and controlling binary outputs, including for driving LEDs. Inputs DI1 to DI6 can only be set as binary. They also work in balanced input mode. Inputs DI / AI7 to DI / AI8 can be set as binary or analog. Input AI9 can only be set as analog. Eight binary outputs are designed to drive LEDs connected in a group with common cathodes...

The C-DM-0006M-ULED module is a 6-channel dimming actuator 0-100% for LED strips in the supply voltage range of 12-48 V DC, with a load capacity of max. 4 A / channel. each channel can be controlled separately. It can also be used as a two-channel RGB actuator, or for two-channel control of the chromaticity of white lighting. The module is designed for a DIN rail switchboard and is connected to the basic module via a two-wire CIB Common Installation Bus®.

C-RI-0401S is a module on the CIB Common Installation Bus®, which contains 2 analog / binary inputs, 1 input for the light sensor, 1 input for the IR receiver demodulator and 1 output for the IR transmitter.

The C-DM-0006M-ILED module is a 6-channel controlled current source for direct control of the brightness of LED chips, ie continuous dimming 0-100% in adjustable ranges of 150 mA, 350 mA, 500 mA, 700 mA, which it generates from an external power supply 48 VDC / 5A. Each channel can be controlled separately. It can also be used as a two-channel RGB actuator, or for two-channel control of the chromaticity of white lighting, etc. The module is designed for a DIN rail switchboard and is...

Built-in module C-WG-0503S is designed for connection of devices communicating via Wiegand protocol, or for connection of analog or binary signals to the system via CIB Common Instalation Bus® and for excitation of LEDs, buzzer, etc., outputs with open NPN collectors . Inputs DI1 to DI3 are designed as 5V TTL with internal pull up resistors. They can be read as binary inputs or evaluate signals from various readers with the Wiegand protocol, such as RFID card readers and the like. Inputs DI...

The C-DM-0402M-RLC module is a 2-channel dimmer for phase control of the intensity of light sources with a resistive, inductive or capacitive character. It is possible to control a load of 2x 500 VA in a 230 V AC / 50 Hz network or a load of 2x 250 VA in a 115 V AC / 60 Hz network. The outputs can be interconnected and in a 230 V AC network the controlled load can be doubled to 1000 VA or even to 2000 VA by connecting all outputs on two modules and their coupled control via the CIB bus. In a...

The C-RQ-0600S module is the basis for several variants of modules designed for the connection of a humidity and temperature sensor, or a CO2 sensor, or an infrared motion sensor and universal analog or binary signals. Universal AI / DI inputs can be set to binary or analog with the possibility of measuring temperature sensors: support sensors PT1000, Ni1000, or a sensor with a NTC12k or KTY81-121 thermistor against a common GND wire. For another type of resistance sensor, a resistance...

The C-DL-0064M module is designed for address control of up to 64 ballasts connected to the DALI bus according to the specification: NEMA Standards Publication 243-2004 Digital Addressable Lighting Interface (DALI) Control Devices Protocol PART 2-2004. As of FW version v.1.5, the module can also be used as a CIB-DSI protocol converter. Signals from both CIB and DALI (DSI) buses are fed to the screw terminals. The power supply of the module is from an external 24 V DC source outside the...

The C-IS-0404S module on the CIB Common Installation Bus® with 4x AI / DI and 4x DO and is built-in. It contains four binary outputs that can be used (in pairs DO1 with DO2 and DO3 with DO4) as 'H bridges' for controlled polarity reversal or as PWM outputs of the open collector type eg for control of model actuators (only with external power supply), or as common transistor outputs 24 VDC 50 mA. It contains four universal inputs configurable in pairs (DI / AI1 with DI / AI2 and DI /...

The C-1W-4000M module is a 2-time low-speed 1Wire bus master designed by DALLAS. Each bus allows the connection of 20 sensors, ie a maximum of 40 sensors per module in total. The module is designed for a DIN rail switchboard. It is connected to the Foxtrot basic module via a two-wire CIB Common Installation Bus®.

Expansion module C-OS-0808M with 8 binary inputs at the level of 24 V DC and 2x4 fast transistor outputs usable for direct control of two unipolar or bipolar stepper motors. Inputs and outputs can also be used universally and can be set manually mode with the buttons on the front panel. The module is equipped with removable screw connectors. The module is designed for a DIN rail switchboard. It is connected to the Foxtrot basic module via a two-wire CIB Common Installation Bus®.

Modules C-FC-0024X is a composition of inputs and outputs designed to control the valves and fan of the FanCoil unit. If the composition of inputs and outputs is satisfactory, it can be used universally. The module contains 3 combined (analog / binary) inputs with a common terminal for connecting contacts or resistors. sensors, 1 analog / PWM output (8 bits, 0-10V) for continuous fan speed control and 2 relay outputs with a common terminal for controlling valves with heating and cooling...

The C-EV-0302M module is intended for controlling the charging of electric vehicles with alternating current according to ČSN EN 61851-1. For charging control and feedback, the module contains CP (Control Pilot) and PP (Proximity function) outputs connected to the charging connector (Type 1, Type 2). Furthermore, the module contains a relay output for controlling the contactor of the power supply to the electric vehicle and one semiconductor output for connection with an external charging...

The C-EV-0302M module is intended for controlling the charging of electric vehicles with alternating current according to ČSN EN 61851-1. For charging control and feedback, the module contains CP (Control Pilot) and PP (Proximity function) outputs connected to the charging connector (Type 1, Type 2). The module also contains relay outputs for controlling the power supply contactor for electric vehicles, one semiconductor output for controlling the charging connector lock, data output for...

Module of a 3-phase 4-quadrant fast electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms. The measurement is indirect, currents are sensed according to current transformers according to the required input range with a unified output of 333 mV. Data is transmitted via the two-wire CIB - Common Installation Bus®

The C-EM-0401M-P035 module is a fast 4-quadrant electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms for four phases. It can be used for one three-phase and one single-phase measurement at the same time as well as for four separate single-phase measurements. The measurement is indirect, the currents are sensed by bushing current transformers in the range up to 35 A, which are part of the delivery. The module has one relay output...

C-EM-0401M; CIB fast electricity meter / quality meter, power supply 230 V AC / DC, 4x U, 4x I - current transformer x: 100 mA, 1x RO The C-EM-0401M-P035 module is a fast 4-quadrant electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms for four phases. It can be used for one three-phase and one single-phase measurement at the same time as well as for four separate single-phase measurements. The measurement is indirect, currents are...