Атол 30Ф не включается (заводской брак)
Валерий
14 января 2022
Запчасти и компоненты для торгового оборудования. Более 5 000 клиентов и более 350 000 товаров! Скрыть
| System components | ||
|---|---|---|
| Emitter | SLP10-3-T | |
| Receiver | SLPC10-3-R | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP10-3-T | |
| Receiver | SLPC10-3-R/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP10-4-T | |
| Receiver | SLPC10-4-R | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP10-4-T | |
| Receiver | SLPC10-4-R/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP30-2-T | |
| Receiver | SLPC30-2-R | |
| General specifications | ||
| Effective detection range | 6 ... 30 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP30-2-T | |
| Receiver | SLPC30-2-R/31 | |
| General specifications | ||
| Effective detection range | 6 ... 30 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP30-3-T | |
| Receiver | SLPC30-3-R | |
| General specifications | ||
| Effective detection range | 6 ... 30 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP30-3-T | |
| Receiver | SLPC30-3-R/31 | |
| General specifications | ||
| Effective detection range | 6 ... 30 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP30-4-T | |
| Receiver | SLPC30-4-R | |
| General specifications | ||
| Effective detection range | 6 ... 30 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP30-4-T | |
| Receiver | SLPC30-4-R/31 | |
| General specifications | ||
| Effective detection range | 6 ... 30 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP65-2-T | |
| Receiver | SLPC65-2-R | |
| General specifications | ||
| Effective detection range | 12 ... 65 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP65-2-T | |
| Receiver | SLPC65-2-R/31 | |
| General specifications | ||
| Effective detection range | 12 ... 65 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP65-3-T | |
| Receiver | SLPC65-3-R | |
| General specifications | ||
| Effective detection range | 12 ... 65 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP65-3-T | |
| Receiver | SLPC65-3-R/31 | |
| General specifications | ||
| Effective detection range | 12 ... 65 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP65-4-T | |
| Receiver | SLPC65-4-R | |
| General specifications | ||
| Effective detection range | 12 ... 65 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Emitter | SLP65-4-T | |
| Receiver | SLPC65-4-R/31 | |
| General specifications | ||
| Effective detection range | 12 ... 65 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter | |
| System components | ||
|---|---|---|
| Transceiver | SLPC8-2-A | |
| Mirror pillar | SLP8-2-M | |
| General specifications | ||
| Effective detection range | 0.2 ... 8 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals | |
| System components | ||
|---|---|---|
| Transceiver | SLPC8-2-A/31 | |
| Mirror pillar | SLP8-2-M | |
| General specifications | ||
| Effective detection range | 0.2 ... 8 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals | |
| System components | ||
|---|---|---|
| Emitter | SLP10-2-T | |
| Receiver | SLPCM10-2-R | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter, muting lamp as well as other muting sensors | |
| System components | ||
|---|---|---|
| Emitter | SLP10-2-T | |
| Receiver | SLPCM10-2-R-L | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for startup readiness, OSSD on, OSSD off, muting lamp, signals in parallel in the lamp socket | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage terminals, M12 connector for transmitters, muting lamp, etc., muting sensors, lamp socket for muting lamp, etc. | |
| System components | ||
|---|---|---|
| Emitter | SLP10-2-T | |
| Receiver | SLPCM10-2-R-L/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for startup readiness, OSSD on, OSSD off, muting lamp, signals in parallel in the lamp socket | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage terminals, M12 connector for transmitters, muting lamp, etc., muting sensors, lamp socket for muting lamp, etc. | |
| System components | ||
|---|---|---|
| Emitter | SLP10-2-T | |
| Receiver | SLPCM10-2-R/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 500 mm | |
| Number of beams | 2 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter, muting lamp as well as other muting sensors | |
| System components | ||
|---|---|---|
| Emitter | SLP10-3-T | |
| Receiver | SLPCM10-3-R | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter, muting lamp as well as other muting sensors | |
| System components | ||
|---|---|---|
| Emitter | SLP10-3-T | |
| Receiver | SLPCM10-3-R-L | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for startup readiness, OSSD on, OSSD off, muting lamp, signals in parallel in the lamp socket | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage terminals, M12 connector for transmitters, muting lamp, etc., muting sensors, lamp socket for muting lamp, etc. | |
| System components | ||
|---|---|---|
| Emitter | SLP10-3-T | |
| Receiver | SLPCM10-3-R-L/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for startup readiness, OSSD on, OSSD off, muting lamp, signals in parallel in the lamp socket | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage terminals, M12 connector for transmitters, muting lamp, etc., muting sensors, lamp socket for muting lamp, etc. | |
| System components | ||
|---|---|---|
| Emitter | SLP10-3-T | |
| Receiver | SLPCM10-3-R/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 400 mm | |
| Number of beams | 3 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter, muting lamp as well as other muting sensors | |
| System components | ||
|---|---|---|
| Emitter | SLP10-4-T | |
| Receiver | SLPCM10-4-R | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter, muting lamp as well as other muting sensors | |
| System components | ||
|---|---|---|
| Emitter | SLP10-4-T | |
| Receiver | SLPCM10-4-R-L | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 separated fail safe semiconductor outputs | |
| Signal output | 1 PNP each, max. 300 mA for startup readiness, OSSD on, OSSD off, muting lamp, signals in parallel in the lamp socket | |
| Switching voltage | Operating voltage -2 V | |
| Switching current | max. 0.5 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage terminals, M12 connector for transmitters, muting lamp, etc., muting sensors, lamp socket for muting lamp, etc. | |
| System components | ||
|---|---|---|
| Emitter | SLP10-4-T | |
| Receiver | SLPCM10-4-R-L/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for startup readiness, OSSD on, OSSD off, muting lamp, signals in parallel in the lamp socket | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage terminals, M12 connector for transmitters, muting lamp, etc., muting sensors, lamp socket for muting lamp, etc. | |
| System components | ||
|---|---|---|
| Emitter | SLP10-4-T | |
| Receiver | SLPCM10-4-R/31 | |
| General specifications | ||
| Effective detection range | 0.2 ... 10 m | |
| Light source | LED | |
| Light type | modulated visible red light | |
| Safety type according to IEC/EN 61496 | 4 | |
| Marking | CE | |
| Target size | static: 32 mm dynamic: 50 mm (at v = 1.6 m/s of the obstacle) | |
| Beam spacing | 300 mm | |
| Number of beams | 4 | |
| Operating mode | Start/restart disable, relay monitor, muting operating modes | |
| Angle of divergence | < 5 ° | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Performance level (PL) | PL e | |
| Category | Cat. 4 | |
| Mission Time (TM) | 20 a | |
| PFHd | 3.54 E-9 | |
| B10d | see instruction manuals | |
| Indicators/operating means | ||
| Diagnostics indicator | 7-segment display | |
| Function indicator | LED red: per receiver channel off: interruption flashes: receiver continuously on: reception with sufficient stability control on the front plate: LED red: OSSD off LED green: OSSD on LED yellow: types of muting operation | |
| Pre-fault indicator | LED red next to receiver flashes | |
| Electrical specifications | ||
| Operating voltage | 24 V DC -15% / +25% , galvanically isolated | |
| Input | ||
| Function input | Relay monitor, start release, muting sensors (max. 4) | |
| Output | ||
| Safety output | 2 relay outputs, force-guided NO-contact | |
| Signal output | 1 PNP each, max. 300 mA for start readiness, OSSD on, OSSD off, muting lamp | |
| Switching voltage | 20 ... 60 V DC, 12 ... 25 V AC rms | |
| Switching current | 0.01 ... 2 A | |
| Mechanical specifications | ||
| Degree of protection | IP65 | |
| Connection | M16 cable gland , terminal compartment with cage-terminals, M12-connector for emitter, muting lamp as well as other muting sensors | |
Товаров: 0
На сумму: 0