LB Зона 2 Pepperl+Fuchs

Компонент аналогового входа Universal Input/Output (HART) LB7104A Pepperl+Fuchs

Каталожный номер: 254847

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006 EN 50303:2000
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator LB4002A2 Pepperl+Fuchs

Каталожный номер: 254718

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		1
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		channel I: 2/3+, 4/5-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator LB4005A2 Pepperl+Fuchs

Каталожный номер: 254719

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator LB4102A2 Pepperl+Fuchs

Каталожный номер: 254723

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		1
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		channel I: 2/3+, 4/5-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator LB4105A2 Pepperl+Fuchs

Каталожный номер: 254726

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator LB4106A Pepperl+Fuchs

Каталожный номер: 254729

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 26 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator with Shutdown Input LB4005C2 Pepperl+Fuchs

Каталожный номер: 254720

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator with Shutdown Input LB4102C2 Pepperl+Fuchs

Каталожный номер: 254724

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		1
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		channel I: 2/3+, 4/5-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator with Shutdown Input LB4105C2 Pepperl+Fuchs

Каталожный номер: 254727

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода HART Output Isolator with Shutdown Input LB4106C Pepperl+Fuchs

Каталожный номер: 254730

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 26 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода Output Isolator LB4101A2 Pepperl+Fuchs

Каталожный номер: 254722

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		1
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		channel I: 2/3+, 4/5-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		no
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода Output Isolator LB4104A2 Pepperl+Fuchs

Каталожный номер: 254725

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Current		0 ... 25 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода Universal Input/Output (HART) LB7004A Pepperl+Fuchs

Каталожный номер: 254846

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		BVS 12 ATEX E 115 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		BVS 12 ATEX E 115 X
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ic] IIC T4
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент аналогового выхода Universal Input/Output (HART) LB7104A Pepperl+Fuchs

Каталожный номер: 254847

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		2 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		4
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Transmitter supply voltage		min. 15 V at 20 mA 21.5 V at 4 mA
Input resistance		15 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA
	Open-circuit	factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA
HART communication		yes
HART secondary variable		yes
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: < 50 &Omega configurable between 0 ... 26 mA
	Open-circuit	deviation of preset output value > 0.5 mA
Load		750 &Omega max.
HART communication		yes
HART secondary variable		yes
Watchdog		output off 0.5 s after serious fault
Digital input
Number of channels		4
Sensor interface
	Connection [2]	volt-free contact
Connection		terminals 1+, 2- 3+, 4- 5+, 6- 7+, 8-
Digital signals (active)
	Switching point: ON	> 2.1 mA
	Switching point: OFF	< 1.2 mA
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram)
	Short-circuit	> 7 mA
	Open-circuit	< 0.1 mA
Digital output
Number of channels		4
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-
Drive capability		12 V / 22 mA
Open loop voltage		min. 22.7 V
Current limit		22 mA
Internal resistor		385 &Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Test current	0.4 mA
	Short-circuit	< 50 &Omega
	Open-circuit	< 0.2 mA
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 100 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		BVS 11 ATEX E 116 X
	Marking	II 3(1) G Ex nA [ia Ga] IIC T4 Gc I (M1) [Ex ia Ma] I II (1) D [Ex ia Da] IIIC
Input
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Rated voltage	250 V field circuits to control and supply circuits
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 60079-26:2007 EN 61241-11:2006 EN 50303:2000
International approvals
ATEX approval		BVS 11 ATEX E 116X
UL approval		E106378
IECEx approval		BVS 11.0068X
	Approved for	Ex nAc [ia] IIC T4 [Ex ia] IIIC [Ex ia] I
Marine approval
	Lloyd Register	15/20021
	Bureau Veritas Marine	22449/B0 BV

Компонент входа напряжения Voltage Converter LB5106A Pepperl+Fuchs

Каталожный номер: 254816

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.45 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	voltage input
Connection		voltage input: 5+, 6-
Measurement range		0 ... 10 V
Smallest span		500 mV
Linearity error		0.1 %
Input resistance		100 k&Omega
Conversion time		max. 100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1) red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIC II (1) D [Ex ia] IIIC
Input
	Voltage	0.9 V
	Current	0.2 mA
	Power	0.2 mW (linear characteristic)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0322
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент выхода переключателя Relay output LB6005A Pepperl+Fuchs

Каталожный номер: 254817

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		1.2 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		4
Field device interface
	Connection	Relay output
Connection		channel I: 1-2 NC, 3 channel II: 6-7 NC, 8 channel III: 9-10 NC, 11 channel IV: 14-15 NC, 16
Relay
	Switching voltage	DC: 30 V AC: 150 V
	Switching current	1 A DC / AC resistive load
	Switch power	DC: 30 W , AC: 60 W
	Minimum load	1 V 1 A
	Electrical life	0.1 mio. cycles
	Contact Material	AgPd gold plated
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Low voltage
	Directive 2006/95/EC	EN 61010-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 130 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA nC IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 61010-1
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
UL approval		E106378
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент выхода переключателя Relay output LB6006A Pepperl+Fuchs

Каталожный номер: 254818

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		1.6 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		8
Field device interface
	Connection	Relay output
Connection		channel I: 1-2 NO channel II: 3-4 NO channel III: 5-6 NO channel IV: 7-8 NO channel V: 9-10 NO channel VI: 11-12 NO channel VII: 13-14 NO channel VIII: 15-16 NO
Relay
	Switching voltage	30 V DC / AC
	Switching current	1 A DC / AC resistive load
	Switch power	30 VA / 30 W
	Minimum load	1 V 1 A
	Electrical life	0.1 mio. cycles
	Contact Material	AgPd gold plated
Response time		20 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 160 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA nC IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 61010-1
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
UL approval		E106378
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент выхода переключателя Relay output LB6101H Pepperl+Fuchs

Каталожный номер: 254825

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.65 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Output
Connection		channel I: 1-2 NC, 3 channel II: 4-5 NC, 6
Minimum load		1 V , 1 mA
Relay
	Switching voltage	DC: 30 V , AC: 230 V , 60 V (UL)
	Switching current	1 A DC / AC resistive load
	Switching power	30 VA / 30 W / 230 VA , 60 W (UL)
	Electrical life	0.5 Mio. cycles
Response time		20 ms (depending on bus cycle time)
Contact Material		AgPd gold plated
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1, 2) yellow: signal (per channel)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Low voltage
	Directive 2006/95/EC	EN 61010-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA nC IIC T4 Gc
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 61010-1
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		PF 08 CERT 1234 X
UL approval		E106378
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа RTD Converter LB5001A Pepperl+Fuchs

Каталожный номер: 254734

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.45 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		1
Suitable field devices
	Field device	resistance thermometer
	Field device [3]	slide-wire sensors
Field device interface
	Connection	2-wire sensor
	Connection [2]	3-wire sensor
	Connection [3]	4-wire sensor
Connection		2-wire connection: 5, 6 3-wire connection: 1, 5, 6 4-wire connection: 1, 2, 5, 6
Measurement range		10 ... 400 &Omega (500 &Omega incl. line resistance)
Slide-wire sensor		10 ... 400 &Omega
Measuring current		200 µA
Smallest span		20 &Omega for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		max. 20 ms without LFD max. 150 ms with LFD
Lead resistance		max. 50 &Omega per strand
Line fault detection		can be switched on/off for each channel via configuration tool
	Short-circuit	< 10 &Omega
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1) red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа RTD Converter LB5004A Pepperl+Fuchs

Каталожный номер: 254741

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.6 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		4
Suitable field devices
	Field device	resistance thermometer
	Field device [3]	slide-wire sensors
	Field device [5]	potentiometer
Field device interface
	Connection	2-wire sensor
	Connection [2]	3-wire sensor
	Connection [3]	4-wire sensor
Connection		channel I: resistance/potentiometer input 1 ... 4 channel II: resistance/potentiometer input 5 ... 8 channel III: resistance/potentiometer input 9 ... 12 channel IV: resistance/potentiometer input 13 ... 16
Measurement range		Pt100 (18-390 &Omega) (500 &Omega incl. line resistance) Pt200 (37-780 &Omega) Pt500 (92-1952 &Omega) Pt1000 (185-3905 &Omega) Ni100 (69-270 &Omega) Ni500 (345-1350 &Omega) Ni1000 (690-2700 &Omega)
Slide-wire sensor		0 ... 10 k&Omega
Measuring current		200 µA
Smallest span		50 &Omega for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		max. 500 ms (4 channels) max. 1 s (for 4x 3-wire Pt100)
Busy after download		5 ... 15 s
Lead resistance		max. 50 &Omega per strand
Line fault detection		can be switched on/off for each channel via configuration tool
	Short-circuit	< 10 &Omega
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: line fault (collective alarm) , red flashing: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа RTD Converter LB5101A Pepperl+Fuchs

Каталожный номер: 254805

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.45 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		1
Suitable field devices
	Field device	resistance thermometer
	Field device [3]	slide-wire sensors
Field device interface
	Connection	2-wire sensor
	Connection [2]	3-wire sensor
	Connection [3]	4-wire sensor
Connection		2-wire connection: 5, 6 3-wire connection: 1, 5, 6 4-wire connection: 1, 2, 5, 6
Measurement range		10 ... 400 &Omega (500 &Omega incl. line resistance)
Slide-wire sensor		10 ... 400 &Omega
Measuring current		200 µA
Smallest span		20 &Omega for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		max. 20 ms without LFD max. 150 ms with LFD
Lead resistance		max. 50 &Omega per strand
Line fault detection		can be switched on/off for each channel via configuration tool
	Short-circuit	< 10 &Omega
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1) red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIC II (1) D [Ex ia] IIIC
Input
	Voltage	2.7 V
	Current	43 mA
	Power	93 mW (trapezoid characteristic curve)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0322
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа RTD Converter LB5104A Pepperl+Fuchs

Каталожный номер: 254810

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.6 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		4
Suitable field devices
	Field device	resistance thermometer
	Field device [3]	slide-wire sensors
	Field device [5]	potentiometer
Field device interface
	Connection	2-wire sensor
	Connection [2]	3-wire sensor
	Connection [3]	4-wire sensor
Connection		channel I: resistance/potentiometer input 1 ... 4 channel II: resistance/potentiometer input 5 ... 8 channel III: resistance/potentiometer input 9 ... 12 channel IV: resistance/potentiometer input 13 ... 16
Measurement range		Pt100 (18-390 &Omega) (500 &Omega incl. line resistance) Pt200 (37-780 &Omega) Pt500 (92-1952 &Omega) Pt1000 (185-3905 &Omega) Ni100 (69-270 &Omega) Ni500 (345-1350 &Omega) Ni1000 (690-2700 &Omega)
Slide-wire sensor		0 ... 10 k&Omega
Measuring current		200 µA
Smallest span		50 &Omega for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		max. 500 ms (4 channels) max. 1 s (for 4x 3-wire Pt100)
Busy after download		5 ... 15 s
Lead resistance		max. 50 &Omega per strand
Line fault detection		can be switched on/off for each channel via configuration tool
	Short-circuit	< 10 &Omega
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: line fault (collective alarm) , red flashing: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIC II (1) D [Ex ia] IIIC
Input
	Voltage	7.14 V
	Current	70 mA
	Power	123 mW (linear characteristic)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0322
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа Thermocouple Converter LB5002A Pepperl+Fuchs

Каталожный номер: 254739

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.45 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		1
Suitable field devices
	Field device [2]	Thermocouple
	Field device [4]	mV source
Suitable sensors
	Sensor	thermocouples U, B, E, T, K, S, R, L, J, N, Pallaplat and mV sources
Connection		cold junction: 1, 2 thermocouple: 5+, 6-
Measurement range		-75 ... mV ... 75 mV
Smallest span		5 mV for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		internal cold junction: max. 120 ms without LFD max. 240 ms with LFD external cold junction: max. 20 ms without LFD max. 80 ms with LFD
Compensation (reference junction CJC)		internal cold junction compensation or external cold junction
Line fault detection		can be switched on/off for each channel via configuration tool ,
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1) red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа Thermocouple Converter LB5005A Pepperl+Fuchs

Каталожный номер: 254800

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		4
Suitable field devices
	Field device [2]	Thermocouple
	Field device [4]	mV source
Suitable sensors
	Sensor	thermocouples U, B, E, T, K, S, R, L, J, N, Pallaplat and mV sources
Connection		channel I: 1+, 2- channel II: 5+, 6- channel III: 9+, 10- channel IV: 13+, 14-
Measurement range		-65 ... 75 mV with LFD , -75 ... 75 mV without LFD
Smallest span		5 mV for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		max. 300 ms (4 channels) without LFD max. 600 ms (4-channel) with LFD
Compensation (reference junction CJC)		internal cold junction compensation or external cold junction
Test voltage		1.5 kV input - input 1.5 kV input - bus and auxiliary power
Line fault detection		can be switched on/off for each channel via configuration tool ,
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: line fault (collective alarm) , red flashing: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/input	functional insulation acc. to IEC 60664-1:2007, rated insulation voltage 50 V, testing voltage 500 V
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа Thermocouple Converter LB5102A Pepperl+Fuchs

Каталожный номер: 254808

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.45 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		1
Suitable field devices
	Field device [2]	Thermocouple
	Field device [4]	mV source
Suitable sensors
	Sensor	thermocouples U, B, E, T, K, S, R, L, J, N, Pallaplat and mV sources
Connection		cold junction: 1, 2 thermocouple: 5+, 6-
Measurement range		-75 ... mV ... 75 mV
Smallest span		5 mV for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		internal cold junction: max. 120 ms without LFD max. 240 ms with LFD external cold junction: max. 20 ms without LFD max. 80 ms with LFD
Compensation (reference junction CJC)		internal cold junction compensation or external cold junction
Line fault detection		can be switched on/off for each channel via configuration tool ,
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1) red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIC II (1) D [Ex ia] IIIC
Input
	Voltage	1.8 V
	Current	43 mA
	Power	67 mW (trapezoid characteristic curve)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0322
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент температурного входа Thermocouple Converter LB5105A Pepperl+Fuchs

Каталожный номер: 254813

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
temperature input
Number of channels		4
Suitable field devices
	Field device [2]	Thermocouple
	Field device [4]	mV source
Suitable sensors
	Sensor	thermocouples U, B, E, T, K, S, R, L, J, N, Pallaplat and mV sources
Connection		channel I: 1+, 2- channel II: 5+, 6- channel III: 9+, 10- channel IV: 13+, 14-
Measurement range		-65 ... 75 mV with LFD , -75 ... 75 mV without LFD
Smallest span		5 mV for 0.1 % accuracy
Linearity error		0.1 %
Conversion time		max. 300 ms (4 channels) without LFD max. 600 ms (4-channel) with LFD
Compensation (reference junction CJC)		internal cold junction compensation or external cold junction
Line fault detection		can be switched on/off for each channel via configuration tool ,
	Open-circuit	> 1 k&Omega
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: line fault (collective alarm) , red flashing: communication error
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 150 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 03 ATEX 2042
	Marking	II (1) G [Ex ia] IIC II (1) D [Ex ia] IIIC
Input
	Voltage	1 V
	Current	71 mA
	Power	62 mW (trapezoid characteristic curve)
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA IIC T4 Gc
Galvanic isolation
	Input/input	functional insulation acc. to IEC 60664-1:2007, rated insulation voltage 50 V, testing voltage 500 V
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010 EN 61241-11:2006
International approvals
ATEX approval		PTB 03 ATEX 2042
UL approval		E106378
	Control drawing	116-0322
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ia Ga] IIC T4 Gc [Ex ia Da] IIIC
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input LB1001A Pepperl+Fuchs

Каталожный номер: 254606

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		2
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 2/3- channel II: 4+, 5/6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (1, 3) red: line fault (per channel) Status LED (2, 4) yellow: signal (per channel)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 110 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input LB1002A Pepperl+Fuchs

Каталожный номер: 541925

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.5 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		3
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	active binary signal 24 V DC
Connection		channel I: 1+, 4- channel II: 2+, 5- channel III: 3+, 6-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		20 ms
Indicators/settings
LED indicator		LED green: supply LED red: line fault, per channel LED yellow: signal (status), per channel
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Input
	Voltage	10.5 V
	Current	35 mA
	Power	92 mW
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
ATEX approval		PF 08 CERT 1234 X
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input LB1008A Pepperl+Fuchs

Каталожный номер: 254613

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power consumption		0.7 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		8
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	Usage without connection to areas where there is a risk of explosion: active signals, mechanical contacts, NAMUR proximity switches, 2-wire sensors If the device has been operated in general electrical systems that are not connected to areas where there is a risk of explosion, the device cannot then be used in electrical systems that are connected to areas where there is a risk of explosion. Usage with connection to areas where there is a risk of explosion: mechanical contacts, NAMUR proximity switches
Connection		channel I: 1+, 2- channel II: 3+, 4- channel III: 5+, 6- channel IV: 7+, 8- channel V: 9+, 10- channel VI: 11+, 12- channel VII: 13+, 14- channel VIII: 15+, 16-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Digital signals (active)		Use in safe area: configurable 24 V 5 V
	Switching point: ON	> 8 V > 2.7 V
	Switching point: OFF	< 3 V < 2.3 V
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 k&Omega
Line fault detection		can be switched on/off for each channel via configuration tool , active signals (24 V, 5 V) without line fault detection
	Connection	mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring
	Short-circuit	< 360 &Omega
	Open-circuit	< 0.35 mA
Minimum pulse duration		1 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Status LED (I) red: line fault
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g 10 cycles frequency range 5 ... 100 Hz transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 130 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-11:2007 EN 60079-15:2010
International approvals
IECEx approval		BVS 09.0037X
	Approved for	Ex nA [ic] IIC T4 Gc
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	Bureau Veritas Marine	22449/B0 BV

Компонент цифрового входа Digital Input LB1009A Pepperl+Fuchs

Каталожный номер: 244407

Описание оборудования
Digital Input

Клиенты

Блог

Атол 30Ф не включается (заводской брак)

Citizen CLP-521 - принтер плохо печатает этикетки (диагностика и ремонт)

Атол 77Ф, отключаем датчики бумаги

PRO CS-80 неправильно сортирует (считает) монеты

Как узнать дату изготовления весов CAS

Подписка

Последнее на форуме